Turbo pump for Agilent 5973 MSD

Technical features Flow rate: 0.03-20ml / min Programmable dosage: from 0-999 ml Suction height (max (more).): 2 mWg Operating pressure (max.): 6 bar (rel.) Weight 0.9 kg Permitted fluid temperature: 5-80°C Permitted ambient temperature: 5-40°C Valve material: Kalrez® FFKM Membrane material: PTFE coating, FFKM Pump head material: PTFE, PP, Stainless steel, PVDF Applications Liquid dosing / measuring Qualitative characteristics Small footprint Simple and intuitive use Manual and analog control and RS232 interface Self-priming, it can run dry Constant and reliable flow rate Available with different material configurations for chemical resistance Simple calibration Pump head materials: PP, PVDF, PTFE Membrane materials PTFE coating, FFKM Valve material: FFKM Kalrez Download the data sheet for further information and accessories. NOT SURE WHICH VACUUM PUMPS YOU NEED? Try following our guide to KNF pumps: VACUUM PUMPS FOR THE LABORATORY Or download the KNF guide: THE IDEAL DIAPHRAGM PUMP FOR EVERY APPLICATION

Laboport SD N 860.3 FT.40.18 is a two-stage pump with an integrated “self-drying” system for automat (more)ic condensate drain. The “SD” series is widely used in laboratories, especially when the vapors are humid and a clean and ecological vacuum is required. Typical applications are: vacuum ovens (for drying chemicals, drying biological samples, heat treatments), autoclaves for sterilizing instruments, containers, filters and textiles. Thanks to the use of anti-corrosion materials, it is possible to vacuum even corrosive products. The heart of the pump is the diaphragm with differentiated structure in PTFE, optimized to guarantee high performance with reduced dimensions and at the same time, long life even in heavy applications. When the humid gases are sucked in, it can happen that condensation forms in the pump head: consequently the performance decreases, considerably increasing the emptying time. To eliminate condensation, the 'drying system' then opens a solenoid valve that allows ambient air to enter the heads. Once the condensation has been eliminated, the solenoid valve closes and the pump sucks from the stove in full capacity. Over time, condensation could form again and then the cycle is repeated. The time interval between one cycle and the next can be adjusted as desired, as well as the duration of the air injection. Technical features Flow rate (max.) 60 l / min Final vacuum (max.) 4 mbar (abs.) Pressure (max.) 1 bar (rel.) Fluid temperature allowed at 5-40°C FFPM valve material PTFE coated diaphragm material Pump head material PTFE Applications Rotary evaporation Centrifugal concentration Distillation Vacuum oven Qualitative characteristics Clean operation, 100% oil-free Corrosion resistant PTFE / FFPM flow path Ideal for extremely aggressive / corrosive gases and vapors Compact, silent and reliable The self-drying system removes condensation without altering the vacuum level Maintenance free Download the data sheet for further information and accessories. NOT SURE WHICH VACUUM PUMP YOU NEED? Try following our guide to KNF pumps: VACUUM PUMPS FOR THE LABORATORY Or download the KNF guide: THE IDEAL DIAPHRAGM PUMP FOR EVERY APPLICATION

Technical features Flow rate 0.5–3.0 l/min Suction (max.) 3 mWg Operating pressure (max.) 1 bar (rel (more).) Permitted fluid temperature 5-80°C Maximum permissible viscosity 150 cSt FFKM valve material Membrane material PTFE coating Pump head material PTFE, PP, PVDF Applications Transfer of liquids Qualitative characteristics Small footprint Simple and intuitive use Manual control Self-priming, it can run dry Splash-proof with IP65 protection rating Available with different material configurations for chemical resistance Maintenance free Pump head materials: PP, PVDF, PTFE Membrane material: PTFE coating Valve material: FFKM Simriz® VERSIONS S (standard): the flow rate can only be set manually, using the knob on the upper side, as shown in the photo. RC (remote control): the range can be controlled remotely, such as from a PC, including a fault alarm; a connection cable will be supplied. Supplied with fittings for 12 mm internal diameter tube. Download the data sheet for further information and accessories. NOT SURE WHICH VACUUM PUMP YOU NEED? Try following our guide to KNF pumps: VACUUM PUMPS FOR THE LABORATORY Or download the KNF guide: THE IDEAL DIAPHRAGM PUMP FOR EVERY APPLICATION

Technical features Flow rate (max.) 30 l / min Ultimate vacuum (max.) 160 mbar (abs.) Operating pres (more)sure (max.) 0.5 bar (rel.) Permitted fluid temperature 5-40°C FFPM valve material Membrane material PTFE coating PPS pump head material Applications Filtration Degassing Drying Aspiration of fluids Solid phase extraction Qualitative characteristics Clean operation, 100% oil free Corrosion resistant Compact, silent and reliable Small footprint It can handle humid vapors without damage Maintenance free Download the data sheet for further information and accessories. NOT SURE WHICH VACUUM PUMP YOU NEED? Try following our guide to KNF pumps: VACUUM PUMPS FOR THE LABORATORY Or download the KNF guide: THE IDEAL DIAPHRAGM PUMP FOR EVERY APPLICATION

MORE DETAILS TO FOLLOW

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOL (more)LOW

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Dostmann professional infrared thermometer ScanTemp 410 Infrared thermometers use this technology to (more) measure the surface temperature of materials, regardless of the proximity or otherwise of the measurement object. Just aim, pull the trigger and read the temperature (response time about 0.5 seconds). Not coming into direct contact with the material, this technology provides the possibility to measure hot, dangerous and difficult to reach materials safely, without contaminating or damaging them. Features: - With circular laser sight - Backlight - Belt bag included - MAX-HOLD function (keeps the highest temperature recorded on the display) Application: Detect problems with keeping a process at temperature Food safety (HACCP) HVAC Electrical maintenance Road construction Commercial printing Plastic molding Car maintenance Technical features Temperature range: -60°C ... +500°C Accuracy: ± 2.0% of reading or ±2°C, whichever is greater Repeatability: ± 1.0% of reading or ±1°C, whichever is greater Elapsed time: 500 ms Spectral response: 8 - 14 µm Display resolution: 0.1°C (4-digit LCD) Working temperature: 0°C ... 50°C Emissivity: 0.95 Distance - spot size: 12:1 Laser: circular laser sight Power supply: 2 AAA batteries Dimensions (L x W x H): 175 x 39 x 79 mm Weight: 180 g Features: maximum temperature; display hold; LCD backlight; custody; °C / °F switchable