MX-S Vortex Mixer

This listing is for a MX-S Vortex Mixer

Benchmark BenchMixer XLQ QuEChERS Shaker/VortexerBenchmark’s BenchMixer XLQ has been designed for us (more)e in QuEChERS and other sample prep methods. Supplied with racks for 50ml tubes held horizontally and 15ml and 1.5/2.0ml tubes held vertically, it takes the place of traditional manual shaking in these applications. Multiple samples can be processed simultaneously in the Benchmixer XLQ’s large capacity racks, saving time and preventing operator fatigue. The vigorous, consistent shaking ensures all samples are exposed to identical conditions within the same batch of samples, as well as between batches. The BenchMixer XLQ creates a true vortex in vertical sample racks by holding the top of the tube stationary while the bottom rotates in a 3.6mm orbit. Time and speed are precisley controlled by the digital microprocessor. A pulse mode allows for more vigorous mixing. Quiet operation, minimal vibration and a long service life are guaranteed by the precisely balanced drive system and powerful motor. Using the BenchMixer XLQ is simple. To load the sample racks, loosen the knobs on the stationary steel rods and raise the top sample plate. One rod is shorter than the other, allowing the plate to be lifted up and swiveled to one side. After samples are loaded, lower the plate into place and tighten the knobs. Select the desired speed and run time on the digital control panel and press start. The BenchMixer XLQ can perform unattended mixing for as little as 1 minute or up to 100 hours. INCLUDED: The Benchmark BenchMixer XLQ QuEChERS Shaker/Vortexer includes: - 7 x 50ml Hortizontal Tube Rack - 50x15ml and 50x1.5/2.0ml Tube Rack - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Safety and resistance for your laboratory OHS advance is designed to guarantee the highest safety st (more)andards. - The durable watertight housing and IP 54 protection rating ensure durability even in the most aggressive environments. - Built-in safety alarms for overload, over temperature and over current will maintain performance over time by stopping agitation - The safe operation of the start and stop knob and the lock key prevent unintentional starts and changes in working conditions. - The built-in vibration sensor with different sensitivity levels will stop the operation and inform you to make sure your OHS is stable and properly fixed. Continuous operation guaranteed and supported by a 3 year extended warranty. First-class performance OHS Advance is the ideal solution for demanding applications operating with viscosities up to 50,000 mPa. The electronically controlled brushless motor of the OHS 60 Advance agitates up to 40 l (H2O) with a maximum torque of 60 Ncm and guarantees maximum durability. SpeedServoTM torque compensation technology maintains constant speed by automatically adapting to changes in viscosity. Set the OHS 60 Advance electronic speed control from 30 to 2000 rpm. Constant Torque at Any Speed The powerful brushless motor and microprocessor control ensure unprecedented performance, highlighting the difference between a conventional rod stirrer and VELP OHS Series rod stirrers. The torque remains constant at any speed, even at maximum. Having a constant torque is a very important parameter for the reproducibility of the analyzes. SmartChuck Technology: Inserting or Removing an Auction Has Never Been So Simple! How often do you have to remove or replace the stirring rod using two hands and see the rod fall into the liquid? SmartChuck ™ technology makes this activity quick and easy with the use of one hand and without special accessories. Two simple movements allow you to unlock the protection ring and remove or replace the stirring rod. In the event that the protection ring is opened during the analysis, the instrument stops shaking, showing a safety message on the display. Intuitive and precise control panel The intuitive 3.5 ”OHS Advance TFT display will guide you to precisely set your working conditions and achieve reproducible results. Show key information at a glance. Real-time information on viscosity variation with a resolution of 1 Ncm. Interact with OHS Advance from the real-time graph showing speed, torque and temperature of your test. The OHS Advance works without surveillance thanks to the timer that can be set from 1min to 99.59h. Ideal operating methods can be defined and programmed for demanding tasks where ramps and interval operations are required. Temperature under control OHS Advance is supplied with a Pt100 temperature probe included in the package. Constantly monitor the temperature of your reaction and set the meter to slow down or stop activity if the temperature reaches a defined value. This is important when you want to prevent exothermic reactions from interfering with your analysis! THE BENEFITS OF OHS ADVANCE CONNECTIVITY The OHS Advance is the only rod stirrer to offer the ability to control and monitor processes via Wi-Fi connection to VELP Ermes and via USB. The VELP Ermes cloud platform allows you to control the OHS Advance from PC, smartphone and tablet through a simple and intuitive web interface. With this platform designed by VELP it is possible to activate the shaking, set a timer, set a method (among those saved on the device), download and share reports with a click. For applications in the pharmaceutical, biotechnology and life science sectors, VELP Ermes can manage OHS Advance localized in clean rooms or other controlled environments, without the need for lengthy safety procedures. With the OHS / CotrollerSoftTM software, VELP offers the possibility to all laboratories that cannot benefit from cloud services, a valid alternative with USB connectivity. The OHS allow you to choose between two different control panels, Digital or Advanced, to better suit the needs of your laboratory. - Digital: precise speed settings; torque indicator; integrated timer. - Advanced: all information at a glance; intuitive; real-time graphs. Very easy to use and comfortable tools. Intuitive control panel equipped with Smartchuck: operations and rod change with one hand, effortlessly. - Mandrel opening: Ø from 1 to 13 mm - Stirring rod diameter for Pass-Through: up to 8.5mm Velp products guarantee you peace and security within your laboratory. - Safety button clearly visible from the front - IP54 protection - Integrated safety sensors CONTROL PANEL OF OHS ADVANCE MODELS A - LCD display B - Display keys C - Stirring speed kond D - Lock key E - Main switch F - Smart Chuck

WARING 800E Variable Speed ​​Laboratory Mixer Model 38BL37 STAINLESS STEEL Mixer / Blender Delivered (more) without bowl 230V - 350W

Continuous or touch mode operation Can be used at 4 to 40°C (maximum 85% relative humidity, non-cond (more)ensing), in an incubator, CO₂ incubator or cooling room The pulsating model has a unique effect that reduces heat development and ensures efficient mixing and disruption Shaking motion: Orbital Circular movement: 4.9 mm Speed ​​range: 300 – 2500 rpm Dimensions (WxDxH): 112 x 178 x 135 mm Weight: 4.1kg Equipped with foam insert for 8 tubes of Ø 14 mm and 8 tubes of Ø 19 mm.

Thermomixer comfort allows simultaneous mixing and temperature control. Potential applications inclu (more)de: enzyme reactions, transformations, denaturations of DNA, RNA and proteins, culture of bacteria and yeasts, bead technology, isolation of plasmids and DNA fragments from agarose gels, immunoprecipitation and hybridization. Two selectable program sequences with incubation, mixing and rest phases with subsequent cooling to 13°C below the ambient temperature and automatic recognition of the thermoblock and display of maximum revolutions. Equipped with a 8x 15 mL block Active Peltier heating element and counter cooling provide wide temperature control Short mix, Intermittent mix and Pause function Timer function: 1 min to 99.59 hours or continuous use Mixing speed range: 300 – 1500 rpm Amplitude: 3mm Incubation accuracy: ± 0.5 (between 20°C and 45°C), ± 2°C (below 20°C and above 45°C) Temperature control range: 13°C below ambient temperature to 99°C Temperature setting: 1°C – 99°C Heating rate: ~5°C/min Cooling rate: 2 – 3°C/min (between 99°C and ambient), 0.5 – 1°C/min (between ambient and 13°C below ambient) Dimensions (WxDxH): 220 x 250 x 125 mm Weight: 3.2kg

This Hamamatsu A4178 Specimen Chamber w/ C2400 Camera was removed from a university lab where it was (more) surplus to requirements. This item is in reasonably good cosmetic condition overall but due to the power supply not being included we are unable to test it. It is sold as untested.

Picarro Cavity Ringdown Spectrometer L1102-i Isotopic H2O System This system was removed from a univ (more)ersity where it was surplus to requirement. It is in very good cosmetic condition with all units powered on, we are unable to test the system further at our facility. This system comprises the following: - Picarro Control PC unit ESP-100 Serial No. 274-CPVU-HBQ58Running Windows XP ProfessionalWith Picarro Software installed - Picarro Cavity Ringdown Spectrometer L1102-i ISOTOPIC H2O Serial No. 278-HBDS-0SF - Picarro Vaporisation Module ISOTOPIC A0211 Serial No. VAP073r236

IKA MS 450 Swirler Type of Movement Orbital Speed Fix 450 RPM Shaking Strole 4.50 mm Features - Con (more)tinuous operation - Simple to use - Only mixes at one speed. Reduces possibility of damaging your solution. - Sturdy zinc die cast casing - Typical mixing time 15-20 minutes - Spare foam inserts available, item # L005338 - Compatible with all MS3 basic accessories - May use with microtiter plate attachment, item # 3426400 The MS450 Swirler is the ideal solution for mixing lyophilized powder with sterile water for injection (SWFI). It gently mixes up to 8 vials at a fixed speed of 450 rpms, ensuring the integrity of your solution. Designed for continuous operation, this simple-to-use mixer reduces the possibility of damaging your solution by operating at a single speed. Its sturdy zinc die-cast casing ensures durability. With a typical mixing time of 15-20 minutes, the MS450 is compatible with all MS3 basic accessories and can be used with a microtiter plate attachment. It features an orbital movement with a 4.5 mm shaking stroke and a permissible shaking weight of 0.5 kg.

LABORATORY INCUBATORS CLW SMART POL-EKO CLW - FORCED AIR CONVECTION CLW Series incubators maintain a (more) constant temperature from 5°C above room temperature to a maximum of 100°C. The CLW models are available from 15 to 1005 liters with latest generation control, quality materials and first-in-class performances. Large touch display, programming, alarms, lock, stainless steel interior are just a small part of what you will find below! Continue reading, you will be surprised! ABSOLUTE CONTROL The SMART control panel is among the most complete you can find on the market. Large symbols and temperature values ​​guarantee comfortable and clear reading, combined with disarming ease of use. The latest generation touch screen responds to commands even if touched with latex gloves and is equipped with a large display: all values ​​are perfectly readable from any angle, regardless of the intensity of the light. DO YOU KNOW THE ADVANTAGES OF AN ADVANCED CONTROLLER LIKE THE SMART PANEL? - Sharp 4.3' color touch screen - Quick and easy data transfer: via LAN or USB - Fast, multi-segment, time and temperature programming - Visual and audible alarms with colored bar on display - Internal memory for programs and data storage - User manual downloadable directly from the controller - Loop function up to 255 times or infinite - Controls can be managed even when wearing latex gloves - Recording of the minimum, average and maximum temperature value for each segment - Overview of the set and current parameters during operation - Operation in temperature or time priority mode - ... and much more More and more? POL-EKO has already thought about it. For those who want cutting-edge functions and the freedom of transfer and remote use, POL-EKO offers you the SMART PRO controller. You can find all the differences between the SMART and SMART PRO panel in our dedicated post: insights on SMART and SMART PRO. With the SMART PRO versions, more accessories and options will also be available. QUALITY FIRST Resistant. Durable. POL-EKO incubators are designed and built to guarantee the best performance. They are a smart purchase, for customers who want to invest in the future of their laboratory. By choosing these products you will have precise results for years and years, repeatable and in complete comfort. The CLW SMART series incubators are built with the best materials and equipped with the most important accessories, to give you a complete and ready-to-use standard product. - Double door: solid external; glass interior - Powder coated sheet metal structure (graphite front panel) - Interior in acid-resistant stainless steel according to DIN 1.4301 - Insulated door with lock - Protection class 2.0 - Protection class 3.1 (DIN 12880) as option → - Stainless steel shelves - USB port for downloading recording data, events, manuals, service - LAN port - Open door alarm - Access port for external sensor - Rear air-flap - Quality control protocol (at +37°C) CLW SMART SERIES The nine models of the CLW series cover most of your needs: from mini stoves to the 1005 liter internal volume model. DETAILS AND ACCESSORIES Every detail of your POL-EKO models is designed to make routine work as simple and comfortable as possible. Below, the front and rear view. 1 - Rating plate 2 - Access port ø30mm for external sensor 3 - Internal glass door (for CL models) 4 - Adjustable feet 5 - Shelf 6 - External solid door 7 - Temperature sensors 8 - Open door sensor 9 - Touch control panel 10 - USB port 11 - Handle with key lock 1 - Main switch 2 - Connector for connecting a hose with nitrogen (only for SLWN models) 3 - Air-flap 4 - LAN port 5 - Fuse 6 - Main power socket C20 OPTIONS POL-EKO allows you to increase the possibilities of your incubator with quality accessories; to better adapt to particular applications or to equip the instrument with safety systems and advanced connections. - Stainless steel shelf - Perforated shelf - Stainless steel basins - LabDesk software - IQ OQ PQ calibration and qualification - Overtemperature protection class 3.1 according to DIN 12880 - Backup battery for the display in case of power failure - Clean contact - LAN cable - Non-standard 20mm access door - Additional 30 mm access door

Dimensions (HxWxD): 1020 x 300 x 605 mm