Radwag 5 μl ÷ 50 μl - RW8-103-20-9 Automatic Pipettes

Gilson PIPETMAN M motorized multichannel Pipette P8x20M 1 - 20 µl - Bluetooth Volume (metric): 1 to  (more)20 µl Number of channels: 8 Compatible tips: DL10, DF30ST, D200 tips

The AP-12.5Y is designed to calibrate multichannel pipettes starting at 10 μl. The device feature (more)s a readability [d] of 0.01 mg and can calibrate up to 12-channel fixed-volume and variable-volume pipettes. Because the pipette calibration on the AP-12.5Y is fully automatic, it is four times faster. The calibration procedure for a 12-channel pipette takes less than 20 minutes, not six hours, on this instrument. When purchasing the AP-12.5Y, you get: two calibrated sensors: THB S and THB W, two weighing pans: standard, and for balance test and calibration, two pumps: a single-channel pump and a four-channel pump The ergonomic design of the AP-12.5Y makes it possible to empty weighing vessels, and their overfilling is signalled by Ambient Light. When calibrating a multichannel pipette, a four-channel pump is used to simultaneously remove water from four vessels, greatly reducing the time required for pipette calibration. After emptying a 12-channel pipette, the AP-12.5Y checks all channels in a single cycle. In addition to a database of pipette calibration reports, the AP-12.5Y includes a database of pipettes that is editable and contains maximum permissible error values according to ISO 8655. The report database, in turn, contains measurements and error values calculated for individual points and volumes. The user determines the format and content of the reports. The AP-12.5Y monitors the ambient conditions using calibrated sensors: THB S (ambient conditions measurement) and THB W (liquid temperature measurement), in accordance with ISO 8655. To calibrate the device with mass standards, the weighing pan must be replaced with a pan dedicated to checking and calibrating the balance (both are included in the standard equipment). The AP-12.5Y can calibrate not only 12-channel pipettes, but also single-channel pipettes.

Gilson PIPETMAN M P20M BT Connected, 2-20uL Pipette Volume Range 2-20uL Adjustable or Fixed Volume A (more)djustable Volume Pipette Type Electronic Air Displacement Features - Bluetooth-enabled electronic pipette enhances accuracy and precision in standard and repetitive pipetting modes - Reduces pipetting fatigue and increases efficiency with minimal force needed for aspiration and dispensation - Features motorized piston for high reproducibility and accuracy, reducing the risk of human error - Offers five pipetting modes: pipette, repetitive, mix, reverse, and custom with up to 10 programmable protocols - Bluetooth connectivity facilitates communication with TRACKMAN Connected, guiding through protocols with real-time feedback - Ergonomic design ensures comfort and ease of use, including a simple push-button operation and tip ejection The PIPETMAN M Connected is a Bluetooth-enabled electronic pipette that offers accuracy and precision in both standard and repetitive pipetting modes. Requiring virtually no pipetting forces to aspirate and dispense samples, PIPETMAN M Connected helps reduce pipetting fatigue and increase pipetting efficiency. The pipette interacts in real-time with TRACKMAN Connected making planning and executing pipetting protocols faster, easier, and more reliable. PIPETMAN M Connected is available in 20 models covering a volume range from 0.5uL to 10mL in single channel, and 0.5uL to 1200uL in multichannel. The motorized piston allows for high pipetting reproducibility and accuracy in all modes. Associated with TRACKMAN Connected and its PipettePilot application, PIPETMAN M Connected reduces the risk of human error by transferring verifiable pipetting parameters and commands in the pipette. The intuitive interface has five pipetting modes for many applications: pipette, repetitive, mix, reverse, and custom. Create and transfer up to 10 custom protocols from PIPETMAN M Connected Software into your pipette. Bluetooth connection enables communication with TRACKMAN Connected and helps guide you through your protocol telling you where, when, and how much to pipette with real-time interactions. Aspirate and dispense with one click of the push button and eject tips with ease. The lightweight and ergonomic design rests comfortably in your hand for maximum pipetting comfort. CLICK HERE TO SHOW GILSON PIPETTE COMPARISON TABLE INCLUDED: The Gilson PIPETMAN M P20M BT Connected, 2-20uL Pipette includes: - Power Supply 5V with AC Adapter and Cable - 4 Battery Side Tags - 4 Ejector Side Tags - Lubricant - Safety Bag - Certificate of Conformity - Operator's Manual - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

Gilson PIPETMAN G P100G, 10-100 uL, Metal Ejector PipetteFeatures - Made of PVDF and stainless steel (more), PIPETMAN Goffers premium durability - One of the lowest pipetting forces commercially available - redesigned piston assembly system and high-quality piston grease,PIPETMAN G guarantees hours of comfortable pipetting. - N G clipejector allows for convenient access to serviceableparts. - Pipettes come in either single or multichannel models equipped with metaltip ejectors - Volume range of 10 to 100µL - 3 Year Manufacturer's Warranty

Gilson Classic Starter Kit, 4 Pipette Kit, P2, P20, P200, P1000 The PIPETMAN® Classic line is one of (more) the world standards in pipetting and offers a wide range of continuously adjustable, air-displacement pipettes with legendary accuracy and precision. The PIPETMAN Classic 4 Pipette Kit provides four pipettes covering volume transfers from 0.2 to 1000µL, which will tackle most laboratory needs. Made of highly resistant materials like PVDF and stainless steel, PIPETMAN Classic offers uncontested durability and reliability. Built-to-last, it is the economical solution for years of pipetting INCLUDED: The Gilson Classic Starter Kit, 4 Pipette Kit, P2, P20, P200, P1000 includes: - P2, P20, P200, and P1000 Models - DL10, D200, D1000 PIPETMAN DIAMOND Tipacks - Four SINGLE™ Pipette Holders - Four PIPETMAN Comfort Handles - The Gilson Guide to Pipetting - The Two-minute Inspection Poster - 1 Year Manufacturer Warranty Gilson Classic Starter Kit, 4 Pipette Kit, P2, P20, P200, P1000 SpecificationsAdjustable or Fixed VolumeAdjustable VolumePipette TypeManual Air DisplacementPipette Models IncludedP2, P20, P200, P1000Pipette Tips IncludedDL10 TIPACK, D200 TIPACK, D1000 TIPACK Pipette RangePIPETMAN Classic Number of Channels1Pack Size1Pack Size UnitPackRequest a Formal Quote

C315 Load Cell Platform Scale Precision weight determination in light industrial environments at an  (more)even lighter price. Wherever fast weighing is important. The C315 scale is equipped with the PUE C315 weighing terminal with a backlit LCD display. This long-established technology guarantees reliability and low power consumption, and most importantly, a very long display life. Don’t worry about robustness The construction of the scale is made of powder-coated steel with a stainless steel weighing pan. This guarantees you work for many years, and what’s more, powder-coated steel is more environmentally friendly than traditional painting methods. You will not run out of energy The scale has two power sources: mains and rechargeable. Thanks to its well-designed electronics and LCD display, the device consumes only 5W of energy, which will allow you to work for up to 8 hours without mains power. You get battery power as standard.

Additional WD-4/3 LCD display has been designed to connect with scales operated via PUE H315, MW-01- (more)Ax, PUE HX7, PUE HY10, PUE5 indicator. It is to be purchased with a scale in a set exclusively. The display is equipped with a stainless steel housing and a cable with 8-pin connector (IP67). Features: Automatic baud rate recognition Screen saver LCD backlight Power supply source: the terminal (scale)

Multifunctional scales TMX H is designed to fast and precise determination of mass in industrial con (more)ditions. TMX H Multifunctional scales TMX H comprises terminal PUE 5 and a weighing platform. Labelling system series TMX H is used to print labels for marking weighted goods e.g. in the process of packing. The program can generate standard labels for single goods. Functionality of the software: a function of weight control (weighing control + / -), previewing weighments carried out on weighing terminal as a table of weighments, simplified reporting module allowing the report to be generated, creation of label templates from labels in weighing terminal, identification of goods by using the code EAN-13 and EAN-128, quick search using the range of barcode scanner, the availability of databases: the operators, products, clients, warehouses, tares (packages), etc. The application enables measurements execution and their record into a local database or on the server. Networked terminals allow transmission of the measurements to the parent database installed on the server. The ability to work with a computer program E2R SYSTEM. Terminal types: PUE 5.15R, PUE 5.19R – resistive touch screen technology. Protection class IP68. High resistance to moisture and dust. In comparison to remaining models, limited brightness and lower resistance to shocks and scratches. Possibility of operation using gloves preventing scratches (latex, material). PUE 5.15IR, PUE 5.19IR – infrared touch screen technology. Protection class IP68. Very high brightness and readability level. High resistance to moisture and dust. High mechanical resistance, possibility of operation using gloves (made of latex, material or even steel chain). PUE 5.15C, PUE 5.19C – capacitive touch screen technology. Protection class IP68. High brightness and readability level. High resistance to moisture and dust, good mechanical resistance. Absolute precision of touch detection, sensing multiple points of touch (multi-touch).

MA X2.IC.A moisture analyzers are hi-tech measuring instruments intended for quick determination of  (more)relative moisture content, dry mass content and other parameters in samples of different substances. MA.X2.IC.A series is equipped with innovative system: the drying chamber can be opened and closed automatically using button or proximity sensors. Such solution allows: Maintaining moisture analyzer clean – operator does not touch moisture analyzer’s housing. Removing any shocks caused by manual closing of the chamber – the chamber closes automatically and always with the same intensity. Achieving high repeatability of opening and closing the drying chamber. Enhancing drying process automation. Enhancing safety of operation by eliminating contact with hot components of drying chamber. Improving operation ergonomics. MA.X2.IC.A series features user-friendly colour touchscreen. Free configuration of the control panel can be done by means of hotkeys, customizable information fields and programmable labels. Drying process can be carried out for any temperature and – thanks to databases – particular drying process may be set for a specific product. Highlights of X2 Series moisture analyzers: Automatic opening and closing of the drying chamber 5” capacitive colour touchpad Modern interface Uncomplicated, intuitive operation Programmable display Drying profiles (standard, mild, step, fast) GLP/GMP printouts-reports Repeatable and customized applications Work optimization due to the use of halogen lamps Capacity and temperature MA.X2.IC.A maximum capacity ranges from 50g/0.1mg to 210g/0.1mg. Moisture content is measured with the 0.01% accuracy (0.001 % for samples bigger than 1.5g). The maximum drying temperature is 160˚C (there is an optional moisture analyzer with 250˚C maximum temperature). An additional element for moisture analyzers that improves their functionality is a water vapour permeability determination set used in tanning industry for determining hygienic properties of leather. Databases: Information system of X2 series moisture analyzers is based on 8 databases, allowing many users to operate product database comprising many samples. Collected measurements may be subjected to subsequent analysis. Collected data is registered in 8 databases: Products (up to 5000 products) Users (up to 100 users) Packaging (up to 100 packagings) Customers (up to 1000 customers) Drying programs (up to 200 drying programs) Drying process reports (up to 5000 drying process reports) Ambient conditions (up to 10000 records) Weighings (up to 50000 records) The results The results obtained using the moisture analyzer (the final result of the drying process): % M – the mass loss in %; displays the mass change recorded during the drying process, expressed as a percentage, % D – the dry mass obtained during the drying process, expressed as a percentage; the result is the portion of the sample that remains on the weighing pan after the moisture has evaporated, % R – the ratio of moisture content to dry mass, obtained during the drying process, expressed as a percentage; the result is the portion of the sample that evaporated during the drying process, g – the sample mass after drying. Interfaces USB interface ensures quick transfer and copying of any results of your work (measurements, reports, databases) to a computer or other moisture analyzer. Remote access to the moisture analyzer allows for online data management. Cooperation with E2R allows for external data management which in turn increases the efficiency and results to the maximum.