Zeiss Plan Neofluar 16X/0,50 Imm Microscope Objective 440530 44 05 30

Manufacturer: Agilent / Keysight Model: N4851A MIPI D-PHY Digital Acquisition Probe S/N: MY47000108  (more)Description: The N4851A MIPI D-PHY acquisition probe and N4861A MIPI D-PHY stimulus probe  enable users to perform real-time digital serial analysis and generate real-time digital serial stimulus of the MIPI D-PHY interface. Both  probes support the CSI-2 (Camera Serial interface) and DSI (Display Serial Interface), enabling users to comprehensively characterize the  behavior of controllers as well as display or camera devices. The Keysight Technologies N4851A acquisition probe and the N4861A stimulus probe  operate in conjunction with Keysight 16800 and 16900 Series logic analyzers to provide the digital serial stimulus and acquisition  capabilities required to independently debug and test MIPI D-PHY components, or integrate your MIPI D-PHY based mobile designs. State Analysis for MIPI D-PHY Compliant Devices • Maximum acquisition speed: 800 Mbps• Voltage level support: Low power and high speed voltage• Protocol support: DSI (Display Serial Interface), CSI-2 (Camera Serial  Interface)• 1 or 2 lane support Monitor Device and System Operation • Real-time acquisition of MIPI D-PHY traffic with hierarchical trace displaying  capabilities• Tracks bus mode changes and bi-directional communication• CSI-2 and DSI Protocol Decoder and Packet Viewer• Triggers on protocol-specific packets, specific bits within a packet, and  protocol violations Additional Capabilities • LEDs show MIPI D-PHY bus status and error conditions• Multiple probing solutions, including flying leads and soft touch• Supports up to 2048 bits for user-defined payload• Customize MIPI D-PHY protocol decoding with B4641A Protocol Development Kit Configuration Considerations • Requires 16800 or 16900 Series logic analyzers with 68-channels or more• High impedance probing for signal integrity E5381A• For stimulus, add a pattern generator and N4861A MIPI D-PHY Digital Stimulus  Probe Option: 010 Items delivered: - N4851A MIPI D-PHY Digital Acquisition Probe- Power Supply The probe is in excellent cosmetic condition and is 100% functional tested -  comes out of operation.Ready for your application.

Manufacturer: Olympus Model: U-SLH Slide Filter with Rotating U-SLH Filter Slider with 4 Positions a (more)nd rotating half beam block Items delivered: - Olympus U-SLH Slide Filter with Rotating Half Side Beam Block

Manufacturer: Meridian Biosciene, Inc. Model: illumipro-10™ Incubator Reader with Thermal Printer P/ (more)N: 610172 S/N: IP2010 Description: The illumipro-10™ is an automated isothermal amplification and detection  system for use with Meridian Bioscience, Inc. illumigene® Loop-Mediated  Amplification products.The illumipro-10™ is intended to be used by trained laboratory professional  users in laboratory settings. Isothermal amplification is carried out by two independently controlled heat  blocks capable of operating between 55 C and 65 C, and within 1 C of the  temperature set point. The isothermal amplification temperature set point is dictated by the  illumigene Assay selected. Isothermal amplification time is monitored by the illumipro-10’s internal timer. When in operation, the illumipro-10 will display  ‘Test in Progress’ as well as block temperature and incubation time remaining. DNA amplification detection is completed by the illumipro-10 optics system. Each  illumipro-10 block contains laser diodes illuminating at 650 ± 20 nm and corresponding detectors monitoring light transmission across each illumipro-10  well. The illumipro-10 performs an initial check of the optics system prior to run start. Observed failures in the optics system disable the instrument  block until the failure can be resolved. After successful optics verification, the illumipro-10 checks for the presence of an illumigene test device in each  well. The illumipro-10 automatically enters a Sample ID of ‘EMPTY WELL’ for all wells that a test device cannot be detected in. The illumipro-10 measures  the absorbance of each illumigene test device at the beginning and end of the isothermal amplification incubation. Sample results are reported as INVALID,  POSITIVE, or NEGATIVE based on the observed change in absorbance. Key Facts: • Optimal flexibility for stat or batch runs• True walk away capability for optimized workflow• Very low maintenance requirements enhance efficiency• Instrument verifications can be performed with in-house personnel Features: • Digital Display (guides users through process)• Automatic system self-check• Reaction Blocks (operate independently)• Barcode reader (for sample ID entry)• Small Footprint (of instrument is only 21 cm x 29.2 cm) Performance features of the illumipro-10 include the following: • Self-diagnostics are performed at power-on and at Run start• Self-diagnostic for Test Device Placement and Optics Path Verification• Lid Closure Detection and Lid Lock Feature• Thermal Heat Block with Optics Detection at each well with Visible Light  Emission/Absorbance (650 ± 20 nm)• Interval Timer with Real-Time Assay Processing Time Display• Simple LCD User Interface for Instrument Set-up, Program Selection and Sample  Identification Input• Barcode Scanner for Sample Identification entry• External Keyboard available for Sample Identification entry• Attached Printer for results reporting• Control of amplification product carry-over through use of the self-contained  illumigene Test Device Items delivered: - Meridian Bioscience illumipro-10 Incubator Reader- Meridian Bioscience illumipro-10 Thermo Printer- Power Cord & Connection Cables- Instruction Manual The incubator reader is in absolutely like new condition and 100% functional  tested.