Schott Ringleiter

The Luminex 100 System is a flexible analyzer based on the principles of flow cytometry that enables (more) you to multiplex (simultaneously measure) up to 100 analytes in a single microplate well, using very small samples. The system delivers fast and cost-effective bioassay results on many assay formats including nucleic acid assays, receptor-ligand assays, immunoassays, and enzymatic assays. The Luminex 100 System is the combination of three core xMAP Technologies. The first is xMAP microspheres, a family of fluorescently dyed micron-sized polystyrene microspheres that act as both the identifier and the solid surface to build the assay. The second is a flow cytometry-based instrument, the Luminex 100 analyzer, which integrates key xMAP detection components, such as lasers, optics, fluidics, and high-speed digital signal processors. The third component is the xPONENT Software, which is designed for protocol-based data acquisition with robust data regression analysis. Multiplexing: Up to 100 analytes per sample (80 on MagPlex microspheres) Dynamic Range (Typical): ≥3.5 logs Read Time: 96-well plate in ≤45 min (up to 12,800 tests/hour) Daily Start-Up/Shut-Down: ≤30 min

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

TECHNE MCS-102L 2-position magnetic laboratory stirrer New equipment in its original packaging Refer (more)ence: MCS-102L This magnetic stirrer is designed for optimal cell culture in suspension and the use of microcarriers. The MCS-102L accommodates 2 1 liter culture flasks Speed ​​range from 0 to 80 rpm Soft start and stop for slow acceleration and deceleration Interval setting option Stainless steel shaking platform with markings for culture flasks Designed to operate in an incubator up to 40°C and 95% relative humidity Type: magnetic, rotating Display: analog Applications: biological samples Rotation speed: Max: 80 rpm (503 rad.min-1) Min: 0 rpm (0 rad.min-1) Temperature range: 40°C (104°F)

PUE HX5.EX terminal is a constructional component of industrial multifunctional load cell scales. It (more) is the most modern RADWAG solution to be used in areas endangered with explosive atmosphere. The HX5.EX is compliant with ATEX directive regulations. The terminal is intended for operation in environment filled with explosive gases and dust, and can be placed in zones: 1/21 and 2/22. Standard version of the terminal is equipped with 2 serial intrinsically safe RS232 communication interfaces, and with one intrinsically safe RS485 interface. They facilitate communication with equipment predetermined for use in hazardous areas. Possibility to add digital inputs/outputs expands the range of instruments compatible with the terminal by robotic elements compliant with ATEX directive. For more demanding customers, RADWAG has developed IM01.EX module, installed in the safe area, which extends the available connector range by Ethernet, USB, 4-20mA/0-10V analog outputs, Profibus DP and additional digital inputs/outputs. This enables communication between the terminal and external devices such as barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. Models There are 4 different models: PUE HX5.EX-1: 2 × RS232, RS485 - standard design, PUE HX5.EX-2: standard design + 4IN/4OUT, PUE HX5.EX-3: standard design + 4IN, PUE HX5.EX-4: standard design + 4OUT. Mechanical Design The housing, made of AISI 304 stainless steel, ensures high ingress protection, IP66 / IP68 (up to 1.5 m immersion). The terminal features 5" colour LCD, covered with polycarbonate protecting it against shocks, and a membrane keypad. Ease of operation, clear menu and intuitive information arrangement on the display guarantee comfort of operation. Hermetic intrinsically safe interface connectors are located on the back side of the housing. Stable bracket enables mounting the terminal either on a flat horizontal surface or on the wall. The device tilt can be easily adjusted. Power Supply The PUE HX5.EX terminal can be connected to the mains only with a certified intrinsically safe power supply, manufactured by RADWAG: PM01.EX-1 power supply intended for operation in hazardous area: zone 1 and 2 where there is a risk of explosion due to mixture of air with vapour, mist or gas, classified as explosion group IIC, IIB and IIA and as temperature class T1, T2, T3, T4. zone 21 and 22 where there is a risk of explosion due to mixture of air with dust, flammable fibres and volatile fuels, classified as explosion group IIIC, IIIB and IIIA. PM01.EX-2 power supply intended for operation in safe area, equipped with intrinsically safe circuits which may be placed in: zone 1 and 2 where there is a risk of explosion due to mixture of air with vapour, mist or gas, classified as explosion group IIC, IIB and IIA and as temperature class T1, T2, T3, T4. zone 21 and 22 where there is a risk of explosion due to mixture of air with dust, flammable fibres and volatile fuels, classified as explosion group IIIC, IIIB and IIIA. IM01.EX Communication Module The terminal’s interface range can be expanded using IM01.EX communication module, connected to the terminal via an intrinsically safe RS485 interface, placed outside the hazardous area. Models: IM01.EX-1 Standard: 2x RS232, USB,4 I/4 O, Ethernet IM01.EX-2 analog output 4-20mA/0-10V IM01.EX-3 12 I/12 O, digital IM01.EX-4 Profibus DP IM01.EX-5 PROFINET IM01.EX-6 CANopen (available soon) IM01.EX-7 DeviceNet (available soon) IM01.EX-8 RS485 IM01.EX: ETHERNET IP (available soon) Multifunctional Software Terminal software facilitates processes such as weighing, parts counting, dosing, and percent weighing. Terminal’s information system is based on databases (users, products, weighings, packaging, formulations, customers) and ALIBI memory which guarantees stored data safety. The interfaces enable communication between the terminal and the accessories intended for operation in the hazardous and non-hazardous areas. Accessories: barcode scanners, printers, external displays, control buttons, light signalling towers and other controlling/signalling devices. The terminal can communicate with systems for automatic process control and superior IT systems.

The HX5.EX scale is a modern weighing instrument assuring fast and reliable measurement in hazardous (more) areas classified as zones 1/21 and 2/22. To ensure precision and excellent measurement repeatability, high quality electronic components are used. The weighing platforms offered in wide range of dimensions and maximum capacities, this combined with excellent metrological parameters enables easy selection of an instrument that meets the most demanding requirements. Standard version of the scale is equipped with 2 serial, intrinsically safe RS232 communication interfaces, and with one RS485 interface. They facilitate cooperation with equipment intended for operation in hazardous areas. Possibility to add digital inputs/outputs extends the range of instruments compatible with the indicator by automatic elements compliant with ATEX directive. More demanding customers can use the IM01.EX module, installed in the safe area, which extends the available connectors by Ethernet, USB, 4-20mA/0- 10V analog outputs, Profibus DP and additional digital inputs/outputs. This enables cooperation with external devices: barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. Scale operation requires use of a dedicated PM01.EX power supply, which is not a standard scale component. To operate the scale, order a selected type of the dedicated intrinsically safe power supply. Power supply types: PM01.EX-1 - power supply for operation in ATEX area. Used when it is required to connect the power supply to voltage source placed in hazardous area. PM01.EX-2 - power supply for operation outside ATEX area. Used when power supply connection to voltage source is carried out outside hazardous area. Complex software enables carrying out many tasks connected with mass measurement, e.g. parts counting, checkweighing and statistics. The scales feature user-friendly graphic interface, which can be customized using widgets. This and the large colour display of high resolution guarantee easy and clear transmission of data on current process. Colour bar graph significantly influences performance by signalling whether the weighing result is within declared thresholds or not.

Hermle 50ml Insert (2pk) The Hermle 50ml Inserts are for use with the 6 x 85ml Rotor for the Z326 an (more)d Z326 K centrifuges. INCLUDED: The Hermle 50ml Insert (2pk) includes: - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW