Mettler Toledo Classic AL104 Analytical Balance Analysenwaage Waage 110g x 0.1mg

RS 232 cable: scale (15-pin connector) – computer (9-pin connector). Cable length: 2 m. Custom (more)ized cable length (extra charge): 5 m, 10 m.

IN/OUT cable (PUE C41H, PUE HY10, PUE 5.15, PUE 5.19). Lenght 5 m. Cable types: Standard P0256.2: 2  (more)m Customized P0256.5 (extra charge): 5 m Customized P0256.10 (extra charge): 10 m Compatible with: Scales operated via PUE C41H terminal Scales operated via PUE HY10 terminal Scales operated via PUE 5.15 terminal Scales operated via PUE 5.19 terminal PUE C41H terminal PUE HY10 terminal PUE 5.15 terminal PUE 5.19 terminal HRP platform MWSH weighing module MWLH weighing module

RS 232 cable: Balance - computer. Cable length: 5 m Compatible with: - Scales with PUE C315 terminal (more) - PUE C315 terminal

Special weighing dishes enable convenient weighing of small samples with high accuracy. The dishes a (more)re dedicated to ultra-microbalances (UYA 5Y series), microbalances (MYA 5Y, XA 5Y.M.A and XA 5Y.M series) and analytical balances (XA 5Y, AS X2 PLUS series, AS R1 and AS R2). The set contains 100 8-ml dishes of 30 x 10 mm. The weighing dishes can be find used wherever it is necessary to weigh a small sample with high accuracy, among others in the pharmaceutical, chemical and food industries.

Radwag laboratory holders have been designed to facilitate faster and more convenient weighing. They (more) ensure perfect and safe fixing of small vessels of typical and non-standard shapes. Features: Maximum weighing ergonomics Direct dosing of a sample into a vessel High efficiency, lower costs (minimized potential loss of samples during transfer) Direct dosing of samples into various vessels (test tubes, round flasks, flat flasks, plastic test-tubes, titration vessels) Laboratory holders are compatible with all Radwag analytical balances. Intended use: glass and plastic tubes filters other vessels

MY11 pipette calibration adapter enables calibration and/or verification of piston pipettes by means (more) of a gravimetric method using the MYA microbalance. Set content: weighing pan weighing vessel evaporation ring glass chamber with an opening for dosing Vessel capacity: 11 ml Evaporation ring is an integral part of the adapter that increases relative humidity inside the weighing chamber. With this evaporation of the liquid during calibration/verification is stopped. An integrated weighing pan enables centric loading of the vessel in the weighing chamber. The weighing pan and the vessel are housed in a glass chamber featuring an opening allowing the user to dispense liquid through it, and reducing air drafts. Adapters for Pipettes Calibration Pipette calibration adapters are intended for calibration and verification of piston pipettes using gravimetric method. Use of the pipette calibration adapter reduces maximum capacity of the balance by the mass of the weighing vessel. The table below, which presents the minimum requirements in accordance with ISO 8655-6:2022 standard, enables to select suitable adapter for pipette calibration and respective balance version. The parameters of the balance have been selected so that the expanded uncertainty of measurement in use is less than ¼ of the maximum permissible error of the test object. Nominal volume of apparatus under test V Resolution (d) mg Repeatability (s)3mg Recommended balance Microbalances Analytical balances 0,5 µl ≤ V < 20 µl 0,001c 0,01d 0,006c, e 0,03d MYA 21.5Y XA 6/21.5Y.M.A XA 6/21.5Y.M XA 21.5Y.M.A XA 21.5Y.M XA 21/52.5Y.M.A XA 21/52.5Y.M XA 53.5Y.M.A XA 53.5Y.M 20 µl ≤ V < 200 µl 0,01 0,025 XA 52.5Y XA 110.5Y XA 82/220.5Y.A XA 82/220.5Y XA 120/250.5Y.A XA 120/250.5Y 200 µl ≤ V ≤ 10 ml 0,1 0,2 Adapter for pipette calibration MY 11 XA 11 XA 11 XA 11 XA 11 XA 17 XA 17 XA 17 XA 100 XA 17 XA 100 Maximum vessel capacity 11 ml 11 ml 11 ml 11 ml 11 ml 17 ml 17 ml 17 ml 100 ml 17 ml 100 ml Weighing vessel mass ~ 10 g ~ 10 g ~ 10 g ~ 10 g ~ 10 g ~ 11 g ~ 11 g ~ 11 g ~ 65 g ~ 11 g ~ 65 g a The repeatability values, in this table, apply in the volumen determination of a single channel pipette. When a single-channel balance is used for volumen determination of single channel pipettes the repeatability values are double the values of this table. c Single-channel balance. d Multichannel balance, only valid for multi-channel pipettes. Multi-channel balances of 0,01 mg readability may be uses to test multi-channel pipettes with nominla volumes below 20 µl only if the expanded uncertainty in use is less than ¼ of the maximum permissible systematic error of the test object. e For single-channel pipettes of nominal volumes of less than 2 µl, a balance with repeatability better than the values in the table shall be used so that the expanded uncertainty in use is less than ¼ of the maximum permissible systematic error of the test object. table {font-size: 12px} td {padding:10px; } tr {text-align:center;} @media (max-width: 800px) { table {font-size: 9px} td {padding: 1px 1px} }

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

ATAGO PAL-BX/RI pocket refractometer New equipment in its original packaging The PAL-BX/RI has a dua (more)l scale of Brix (Full range: Brix from 0.0 to 93.0%, high measurement accuracy: Brix ± 0.1%) and Refractive Index (resolution 0.0001). The Refractive Index and the measurement temperature scroll continuously along the screen. The PAL-BX/RI works perfectly for measuring almost any sample. Model: PAL-BX/RI Cat.No. : 3852 Range: Brix: 0.0 to 93.0% Refractive index: 1.3306 to 1.5284 Resolution: Brix: 0.1% Refractive index: 0.0001 Accuracy: Brix: ±0.1% Refractive index: ±0.0003 (water 20ﾟC) Temperature correction: 10 to 100ﾟC (Brix only)

Block: Gold anodized 96 well block Max Heating Rate: 3.5°C/sec Max Cooling Rate: 2.5°C/sec Avg Heati (more)ng Rate: 3.0°C/sec Avg Cooling Rate: 2.0°C/sec Temperature Uniformity 55°C: ± 0.20°C within 15 sec Temperature Uniformity 70°C: ± 0.30°C within 15 sec Temperature Uniformity 95°C: ± 0.60°C within 15 sec Block Temperature Range: 3°C to 99°C Gradient Temperature Range 20 to 99 °C Control Accuracy +/- 0.1 °C Block Format: 96 well (70µl) Memory: 350 typical programs in up to 30 user directories (password protected) Auto restart after power failure: Yes Lid Temperature Range: 30 to 99°C Dimensions (WxDxH): 280 x 380 x 240 mm Weight: 13.0 kg

PMV 50.5Y moisture analyzer is an advanced solution for measurement of moisture content of samples c (more)ontaining significant amount of moisture (up to 100%). The drying process is carried out by means of microwaves which enable to evenly heat the whole sample’s volume. The PMV 50.5Y, when compared to standard moisture analyzers, significantly shortens the drying time. The PMV 50.5Y microwave moisture analyzer can be successfully used wherever materials containing large amounts of water are dried. These materials are, for example, dairy products, fish, meat, fruit products, syrups, creams or liquid resin. The sample is placed in the drying chamber on a glass fibre filter. At the bottom of the chamber there is one end of the waveguide from where the microwaves are emitted. Upon process start, microwaves are equally distributed on the filter’s surface and dry the sample. The moisture content is determined on the basis of the mass loss obtained during drying. A respective drying program is selected depending on sample mass and its chemical composition. The average duration of this process depends on the type and mass of used substance, and takes 1 to 10 minutes. In contrast, drying using the traditional halogen moisture analyzer takes 5 to 40 minutes. The PMV 50.5Y microwave moisture analyzer is equipped with a temperature sensor and enables to monitor device power in order to prevent exceeding the boiling point during the process. A preset microwave power is displayed on the indicator throughout the drying procedure. The PMV 50.5Y’s main features: intended for drying of samples containing significant amount of moisture (up to 100%), ultra-short drying time when compared to traditional moisture analyzers and standard drying methods, microwave-based solution, uniform heating of entire sample’s surface, complex database of drying programs, finish mode: manual, automatic, time-defined, user-defined, advanced reports, time and statistical graphs, easy operation due to a touch screen. The PMV 50.5Y moisture analyzer is based on an advanced-class Y series system intended for laboratory balances. Expanded 16 GB memory enables saving and storing sophisticated reports and time and statistical graphs. Wireless communication improves ergonomics and operation safety. Wi-Fi® enables sending data between the moisture analyzer and a mobile device. Large 10’’ touch screen guarantees comfort of operation. Proximity sensors ensure touch-free access to user-specified operations. For each purchase of the PMV 50.5Y moisture analyzer the customer is supplied with: 60 glass fibre filters of ø90 mm, a sample of sodium chloride 10% ± 0,5% to determine correctness of the operation at the workstation, a service concerning determination of drying parameters for five customer-selected samples carried out by RADWAG employee. The results obtained using the moisture analyzer (the final result of the drying process): % M – the mass loss in %; displays the mass change recorded during the drying process, expressed as a percentage, % D – the dry mass obtained during the drying process, expressed as a percentage; the result is the portion of the sample that remains on the weighing pan after the moisture has evaporated, % R – the ratio of moisture content to dry mass, obtained during the drying process, expressed as a percentage; the result is the portion of the sample that evaporated during the drying process, g – the sample mass after drying. * All trademarks and registered trademarks are the property of their respective owners. Terminal 5Y in Microwave Moisture Analyzer With the 5Y terminal, microwave moisture analyzer PMV gain new capabilities and functionalities, such as: 10-inch display, Digital Weighing Auditor (DWA), uncompromised user verification, Ambient Light, hotspot, RFID*, Live Note voice and text notes, voice commands for the device, measurement history within the Handy Library, widgets. Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13,56 MHz

The Interflow cross flow unit has been developed to protect the object in the workspace of the cross (more) flow unit against external influences and contamination. The operation of the cross flow is based on the principle of the laminar (air) flow technique. This is an air flow which, after flowing through the filters, is virtually dust- and germ-free and flows through the workspace at a specific speed and according to a specific pattern. In this way, dirty air from outside the cross flow unit does not get a chance to enter the workspace. Absolute filter Type: TA2DS14G2F3XNCT Dimension: 610 x 1830 x 70 mm Quantity: 1 Pre-filter Type: V50 Cassette Dimension: 500 x 250 x 50 mm Quantity: 3 Fan Type: DD 9-7 TH ECM2 1/2 Quantity: 2 Relief Fixture: LED strip Type: Linear Flex Ulta Plus Watts: 1640 lm/m Color: 4000K (White) Light intensity: > 800 Lux Dimensions (WxDxH): 1860 x 792 x 1144 mm

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW