Offering the best quotes for your research!
New and used scientific instruments
🚚 Shipping Worldwide 🌎
✉️ info@questpair.com
Yamato DT-611 Forced Convection Clean Oven, 216L, 220V
Product Description
The Yamato DT-611 is a Class 100 forced convection cleanroom oven designed for precise temperature control in dust-free environments. It supports drying, sterilization, and heating applications with temperature control up to 360°C.
- Circulation Method: Forced convection
- Operating Temperature Range: Room temperature +30°C to 360°C
- Temperature Control Accuracy: ±0.3°C at 360°C
- Temperature Fluctuation: ±0.5°C at 360°C
- Temperature Distribution Accuracy: ±4.0°C at 360°C
- Temperature Gradient: ±20.0°C at 360°C
- Maximum Temperature Reaching Time: Approximately 80 minutes
- Clean Level: Class 100 when temperature stable
- Interior/Exterior Material: Stainless steel interior, cold rolled steel plate with melamine resin baking finish exterior
- Insulation: Glass wool
- Door: Single side left swing
- Heater: Stainless steel pipe heater controlled by Triac zero-cross control
- Fan: Sirocco fan with 400W condenser motor
- Filter: Heat resistant HEPA filter with >99.97% efficiency for 0.3μm particles
- Differential Pressure Meter: Analog, range 0–300 Pa
- Caster Wheels: Free swivel casters without stopper, with level adjusters
- Temperature Control/Setting: PID V control with digital ▲/▼ key setting
- Temperature Display: Dual LED displays; green 4-digit and orange 5-digit, resolution 1°C
- Operating Functions: Constant temp., program operation up to 99 steps and 99 patterns, duration/time select, auto start/stop
- Additional Functions: Variable fan speed, accumulated operation time (up to 65,535 hrs), power consumption and CO2 emission monitoring, calibration offset, power recovery, data save/restore
- Sensors: Dual K-type thermocouples; one for control, one for independent overheat prevention
- Safety Features: Self-diagnostics (sensor failure, triac short circuit, overheating prevention, fan motor failure, heater line disconnect, relay damage), earth leakage breaker, key lock, phase reversal relay, door switch disabling heater and fan when open
- Earth Leakage Breaker: 20A, 30mA rated sensitivity
- Internal Dimensions (WxDxH): 600 × 600 × 600 mm
- External Dimensions (WxDxH): 850 × 1175 × 1720 mm
- Internal Capacity: 216 L (7.62 cu. ft.)
- Weight: Approximately 270 kg (596 lbs.)
- Shelving: 3 shelves with 6 brackets, 17 steps for pitch adjustment at 30 mm intervals, load capacity approx. 30 kg per shelf
- Power Supply: 220V, 3 phase, 14A, 50/60 Hz (±10%)
This oven is optimized for cleanroom applications requiring precise temperature uniformity and advanced monitoring capabilities, suitable for drying, sterilization, and temperature testing.
Item Stats
Product details
| Circulation Method | Forced convection |
| Operating Temp. Range | Room temperature +30 to 360°C |
| Temp. Control Accuracy | ±0.3°C at 360°C |
| Temp. Fluctuation | ±0.5°C at 360°C |
| Temp. Distribution Accuracy | ±4.0°C at 360°C |
| Temp. Gradient | ±20.0°C at 360°C |
| Max. Temp. Reaching Time | ~80 mins. |
| Clean Level | Class100 (when temperature is stable) |
| Interior/Exterior Material | Stainless steel / Cold rolled steel plate with melamine resin baking finish |
| Heat Insulating Material | Glass wool |
| Door | Single side left swing |
| Heater | Stainless steel pipe heater |
| Fan Type | Sirocco fan, Condenser motor 400W |
| Differential Pressure Meter | Analog type (0 ~ 300Pa) |
| Cable Port/ Exhaust Port | Inner diameter: 33mm×1 (right side) / Outer diameter 61mm |
| Filter | Heat resistant HEPA filter (dust-collection efficiency >99.97% up to 0.3μm particle filtering) |
| Caster Wheels / Adjuster | Free swivel caster wheels without stopper / level adjuster (2 at front) |
| Temp. Control/Setting Method | PID V control / Digital setting with ▲/▼ keys |
| Temp. Display System | Top screen: green 4-digit digital LED (resolution 1°C), Bottom screen: orange 5-digit digital LED (resolution 1°C) |
| Other Indications | LED indicates temperature patterns for heating/stabilizing/cooling |
| Operation Functions | Constant temperature operation, Programmed operation (Maximum 99 steps, up to 99 patterns, repeat operation function),Duration/time select operation function (auto start/auto stop/quick auto stop, program operation) |
| Additional Functions | Variable fan speed, Accumulated on time, operation time function (up to 65,535 hours); calibration offset; accumulated powerconsumption monitoring, total CO2 emission monitoring, heater output monitoring; power recovery; setting data save and restore |
| Sensor | K type Thermocouple dual sensor (temperature control and independent overheat prevention device sensors) |
| Heater Control | Triac with zero-cross control |
| Safety Device | Self-diagnostic functions (Detection for Temp. Sensor Failure, Triac Short Circuit, Automatic overheating prevention, Fan motorfailure detection, Heater Line Disconnect, Main Relay Contact Damage), Earth leakage breaker, Key Lock Function, Independentoverheating prevention device, Phase reversal relay, Door switch |
| Earth Leakage Breaker | 20A, Current leak /short circuit/surge protection, rated sensitivity 30mA |
| Door Switch | Door open: fan motor and heater circuit off, Door close: fan motor and heater circuit on |
| Internal Dimensions WxDxH | 600×600×600 mm |
| External Dimensions WxDxH | 850×1175×1720 mm |
| Internal Capacity | 216L / 7.62 cu. ft. |
| Weight | ~270 kg / 596 lbs. |
| Shelf Rest / Pitch | 17 steps / 30mm |
| Withstand Load Of Shelf | ~30 kg / shelf |
| Power Supply 50/60Hz (V±10%) | 220V 3 phase 14A |
| Shelf Plate / Bracket | 3 pcs. / 6 pcs. |
Documents
About QuestPair
Our Mission
QuestPair is Europe's leading platform for scientific equipment, connecting researchers and organizations with verified suppliers of both new and pre-owned laboratory instruments in the biotech and material science industry. Our aim is to make the procurement of scientific instruments more efficient, cost-effective, and reliable, so that laboratories can focus on advancing science rather than searching equipment and negotiating deals.
Why Choose Us
Founded by scientists for scientists, we understand your challenges. Our AI-powered platform offers transparent pricing, verified quality, and expert support, ensuring you find the perfect equipment for your research needs.
Verified Quality
Every piece of equipment undergoes thorough verification by our expert team, ensuring reliability and performance.
Cost Efficiency
Access both new and premium pre-owned equipment, saving up to 40% without compromising on quality.
Expert Support
Our dedicated team provides personalized guidance throughout your equipment procurement journey.
Ready to Transform Your Research?
Join thousands of biotech scientists who trust QuestPair for their equipment needs.
What customers think about QuestPair
Brilliant service. Everything arrived and was exactly as expected
Jon Welburn
Great customer service! Got me great options for the equipment I was looking for and in a timely manner.
Pamela
Space Lab Technologies, LLCHarm is very responsive to help me find the right equipment. The product I received is in a good condition.
Ph.D. Hsin-Wen Liang
Northeastern UniversityFrom €20,650.30*ex. VAT
In Stock
Get a quote within one business day
Verified equipment
Trusted warranties & returns
Safe payment and fast delivery
Didn't find what you're looking for?
Our sales team specializes in sourcing custom and hard-to-find products to meet your exact specifications. Submit a request for a tailored quote.
Frequently Asked Questions
Is this equipment new or refurbished?
How long does shipping take?
What about warranty and returns?
Why request a quote?
Need help choosing the right tool?
- Accurate policy information specific to your chosen product
- Clear understanding of warranty coverage and terms
- Detailed return policy explanation
- Transparent shipping options and costs
Customer Service
Here to help you with: Product Inquiries, Shipping & Support, Technical Support, Business Inquiries and Press.
We are available to assist you Mon-Fri, 10am - 5pm CET.