IKA ET B Basic Yellow Line Einhängethermostat Immersion circulator 5L/min …250°C

Heating thermostat from 20 to 200°C, with LCD display and simple programming functions LAUDA ECO sta (more)nds out for its range of features and ease of use. ECO thermostats are available in Silver (LCD display; simple programming) and Gold (TFT color display; complex programming) models, equipped with a mini USB interface as standard. A LAUDA innovation is the pressure flow controller located on the front of the head. This means that flow regulation between inside and outside is possible even during operation. - Monochrome LCD graphic display for simultaneous indication of actual and set values - The circulation pump can be adjusted to six levels - Integrated programmer: 1 program with max. 20 segments - Fully electronic continuous regulator with PID action - Additional key Tmax for overtemperature protection - The ECO heating thermostat line includes transparent baths up to 100°C and stainless steel up to 200°C - The most powerful units are equipped with the energy-saving LAUDA SmartCool system - Variants in 230V; the 50 Hz are also available with natural refrigerants - Convenient operation with softkey cursor - Safety class III for operation with flammable and non-flammable liquids. - mini-USB interface - Pump connections with 13mm plastic nipples as standard LAUDA tank thermostats are equipped as standard with a cooling coil. The E 4 model is also equipped with a lid for the bowl and connections for external applications. A drain cock on the rear side makes changing the heat transfer liquid easy and safe. Heating performance graph of ECO Silver immersion thermostats with stainless steel tank. Performance graph of the pump pressing on the six levels. TECHNICAL VISUALIZATION Display 1 - Status display 2 - Display of the internal or external temperature value (T-int or T-ext) 3 - Soft-key bar Control panel 4 - Soft keys, left and right 5 - Enter key 6 - Cursor keys for Up, Down, Left and Right. 7 - T max key: display and adjustment of the overtemperature switch-off point 1 - USB interface 2 - Upper module receptacle approx. 51 mm x 27 mm for analog, RS 232/485 module, Profibus module and contact module 3 - Lower module receptacle approx. 51 mm x 17 mm for Pt100/LiBus module 4 - Connection socket 75S for control cable of cooling underpart for RE 1050 S 5 - Rating label 6 - Connection socket 51H for power supply between the control head and cooling underpart 7 - Mains connecting lead 1 - Cooling coil connections 2 - Pump connection: outflow and return (as standard only with E 4 S and ET 15 S) 3 - Four feet 1 - Mains connecting lead 2 - Rating label 3 - Bath draining tap 4 - Bath drain point

ECO Silver Lauda - Cooling Thermostat LAUDA ECO with reliable technology and modern design for tempe (more)rature ranges from -50°C to 200°C depending of the models. Microprocessor management and integrated cooling system. Silver (monochromatic LCD graphic display), both equipped with mini USB interface. They are distinguished by their range of functions, ease of use and clarity of the display, allowing maximum comfort of use for the operator. These models offer the highest performance conveyed by the LAUDA SmartCool intelligent system, for maximum energy savings. The circulation pump can be adjusted to six levels and the comprehensive range of ECO devices offers cooling capacities from 180 to 700 watts. Refrigerated thermostats comes standard with tank lid, pump connections and are available with air and water cooling. A drain cock on the back of the device makes changing the liquid in the tank easy and safe.Thermostatic bath/circulator with latest microprocessor technology and integrated cooling system MAIN FEATURE • Monochrome grafic LCD display for simultaneous indication of actual and set value • User friendly menu navigation in plain language • Easy input via cursor and soft keys. Additional Tmax key for overtemperature protection • Fully electronic continuous controller with PID action • Safety class III for operation with flammable and non-flammable liquids. Overtemperature cut-out adjustable via menu • Vario pump with six adjustable performance levels • Easy control of the flow rate between internal and external circulation during operation without contact with the bath • USB interface as standard • Upgradeable with an interface module (analogue module, contact module, RS 232/485 module, Profibus, Ethernet-USB module) • Upgradeable with Pt 100/LiBus module for external control and remote control via Command console • Integrated programmer, 1 programme with max. 20 segments • Pump connectors with plastic nipples 13 mm as standard • Bath vessel made from stainless steel with drain valve • Condenser cooling Air • Utilizes natural refrigerants Graph of cooling performance of ECO Silver LAUDA cryostats. Performance graph of the pump pressing on the six levels. TECHNICAL VISUALIZATION Display 1 - Status display 2 - Display of the internal or external temperature value (T-int or T-ext) 3 - Soft-key bar Control panel 4 - Soft keys, left and right 5 - Enter key 6 - Cursor keys for Up, Down, Left and Right. 7 - T max key: display and adjustment of the overtemperature switch-off point 1 - USB interface 2 - Upper module receptacle approx. 51 mm x 27 mm for analog, RS 232/485 module, Profibus module and contact module 3 - Lower module receptacle approx. 51 mm x 17 mm for Pt100/LiBus module 4 - Connection socket 75S for control cable of cooling underpart for RE 1050 S 5 - Rating label 6 - Connection socket 51H for power supply between the control head and cooling underpart 7 - Mains connecting lead 1 - Pump connection: Outflow and return with fittings 13 mm diameter (plastic) 2 - Bath cover 3 - Front grip recess 4 - Ventilation grill (both sides) 5 - Front panel (removable without tools) 6 - Four feet 1 - Rating label 2 - Control cable of cooling underpart (only with RE 1050 S) 3 - Rear grip recess 4 - Connecting lead between the control head and cooling underpart 5 - Bath draining tap 6 - Bath drain point 7 - Ventilation grill

VELP FOC 250I Refrigerated Thermostat Incubator / Drying Oven Total volume: 225 litres FOC225I Usefu (more)l internal volume: 196 litres Temperature range: 3.0 to 50.0 ° C Internal temperature indicated by a display Temperature resolution: 0.1 ° C Electronic thermoregulation system: AUTO-TUNING 2 internal electrical outlets Number of shelves included: 4 Power: 350W Weight: 40 kg Dimension (WxHxD): 540x1300x560mm (21.6x23.2x23in) With internal glass port Continuous ventilation and the Auto-Tuning thermoregulation system ensure temperature uniformity throughout the chamber. The temperature can be set from 3 to 50 °C, the reading on the display refers to the actual internal temperature. The FOC 225I is equipped with two internal sockets controlled by an external switch

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Proline heating thermostat with tank Proline clear-view LAUDA thermostats have been designed for dir (more)ect observation of objects. They are ideal for use with LAUDA Scientific PVS or iVisc automatic viscometer, as the necessary temperature stability for precise viscosity determination is ensured over the entire temperature range. In addition, the two-chamber principle always guarantees a constant liquid level in the measuring chamber, regardless of the volume and temperature of the medium. PVL models with five layers of insulating glass are suitable for low temperature measurements down to -40° or -60°C when a low temperature chiller or thermostat is connected. These thermostats are available with two different control units. The Master version is designed for all applications where the parameters are not changed very often. The removable Command operating unit (PV C models) incorporates a graphic LCD screen for high operating convenience and a programmer. Notable features - LAUDA Vario Flex pump (pressure pump) with eight selectable power levels - Cooling coil fitted as standard with connection for additional cooler Accessories included Fittings for pump connection, cooling coil Specific features of the Proline PV 24 model - Tank volume min. 19 L - Tank volume max. 24 L - Tank opening 405 x 135 mm - Bowl depth 320 mm - Usable depth 285 mm - Upper height of the tank 390 mm - Master control panel; calibration point, timer, under / over temperature alarms, digital indicators - Pump pressure mx. 1.1 bar - Water-cooled temperature range from 20°C to 230°C - Operating temperature range from -60°C to 100°C - Pump connectors M16 x 1 - Fitting 13 Ø

Manufacturer: HTG Model: Firefly Imaging System P/N: 90006 S/N: FF-0025 YoM: 2008 Description: The  (more)FireFly is a high-quality, highly sensitive, luminescent imager with a charge coupled device (CCD) camera that can image multiple targets for an entire 96-well plate in about 15 minutes, allowing researchers to analyze samples directly at their workstation in the laboratory.The system optimizes imaging for HTG’s ArrayPlate qNPA™ technology; a high throughput array that enables multiplexed measurement of RNA levels, DNA expression and protein function. HTG’s ArrayPlate qNPA technology is used to carry out quantitative multiplexed, gene-based drug discovery programs, including target validation, HTS lead optimization, metabolism, toxicology and clinical development.The HTG FireFly Bench Top Chemiluminescent Imager has been specifically designed for use with qNPA kits for directly measuring gene expression on multiple targets simultaneously in a wide range of sample types including formalin-fixed paraffin-embedded tissues without the need for extraction or amplification. The imager allows laboratory researchers in smaller labs to perform studies that previously were not possible due to budget constraints. Applications: - drug discovery - molecular diagnostic such as target gene validation, gene expression screening and time course studies. - in vitro and in vivo pharmacology- metabolism and drug safety studies performing treatment profiling, dose response curves and compound optimization. Features: - Low background and exceptionally high resolution enables researchers to discriminate extremely small changes, < 20 %, in target gene level activity with great confidence, providing the highest quality data to make critical decisions in their research.- Ability to read partial plates allowing increased cost effectiveness in matching plate use to a research budget.- Expandable capacity to read additional formats planned for future software versions.- Simplified, robust optical design that allows high-quality gene-expression experiments on the bench. The HTG FireFly also has a small footprint.- Proprietary light amplification technology increases sensitivity without the need for a cryogenically cooled CCD chip.- The software has been designed to allow researchers sophisticated control over the imager. The instrument’s graphic user interface is intuitive and easy to use. This makes it ideal for multi-user environment where scientists can read plates quickly without overly complex instrument controls. Items delivered: - HTG Firefly Imaging System Condition: The item is in perfect cosmetic as well as working condition. It is 100% functional tested and ready to be operated.

Centrifuge CupsManufacturer: Heraeus Modell: Sorvall 75006449 Q Specification:- max. load 500 g- max (more). 4600 rpm- autoclavable 121°C Items delivered:- 2 cups for centrifuge Condition:The cups are in good used condition.

OHS are designed to ensure the highest safety standards. The resistant sealed case and the IP 54 deg (more)ree of protection guarantee durability over time even in the most aggressive environments. Continuous trouble-free operation in your lab, backed by a 3-year extended warranty. Constant torque at any speed The powerful brushless motor and microprocessor control ensure unprecedented performance, highlighting the difference between a conventional shaft stirrer and VELP OHS Series shaft stirrers. Thanks to the SpeedServo feedback system, the torque remains constant at any speed, even at maximum. Always having a constant torque is a very important parameter for the reproducibility of the analyses. SmartChuck Technology: Inserting or Removing an Auction Has Never Been So Simple! How often do you have to remove or replace the stirring rod using two hands and see the rod drop into the liquid? SmartChuck™ technology makes this activity quick and easy with just one hand and no special accessories. Two simple movements allow you to unlock the protective ring and remove or replace the stirring rod. If the protection ring is opened during the analysis, the instrument interrupts the stirring, showing a safety message on the display. Maximum Protection and Security OHS Advances guarantee the highest safety standards. The IP54 degree of protection ensures maximum protection of the instrument from corrosion and high performance in challenging work environments. The stirring is activated through pressure, avoiding involuntary start-ups and the set speed is reached gradually. The large number of sensors and safety controls deactivate the stirring in case of overload, overheating or short circuit. Integrated Timer to Schedule Your Activities The OHS Digitals are equipped with timers that allow you to program the stirrer according to your needs and to carry out the reactions independently. Setting the timer is quick and easy, just press the dedicated button and select a time interval between 1 min and 99:59 hours. The OHS allow you to choose between two different control panels, Digital or Advanced, to better suit the needs of your laboratory. - Digital: precise speed settings; torque indicator; integrated timer. - Advanced: all information at a glance; intuitive; real-time graphs. Very easy to use and comfortable tools. Intuitive control panel equipped with Smartchuck: operations and rod change with one hand, effortlessly. - Mandrel opening: Ø from 1 to 13 mm - Stirring rod diameter for Pass-Through: up to 8.5mm Velp products guarantee you peace and security within your laboratory. - Safety button clearly visible from the front - IP54 protection - Integrated safety sensors CONTROL PANEL OF OHS DIGITAL MODELS A - 7 Segment Display LED B - Torque indicator bar C - Low speed LED (only OHS 200) D - Gear key (only OHS 200) – Timer key for other models E - High speed LED (only OHS 200) – Timer LED for other models F - Speed control knob G - Timer LED (for OHS 200) - Upper lock LED for other models H - Timer key (for OHS 200) – Lock key for all models I - Lower Lock LED J - Main switch K - Smart chuck

The Biostat B-DCU is a fermenter/bioreactor specifically designed to accommodate the requirements of (more) process optimization and characterization in the biotech and biopharmaceutical industry. It provides enhanced functionality and an unrivalled level of options for cell culture and microbial processes making it the ideal scale-down model for your large scale process. Supply Tower

IKA Eurostar 200 Control P4 Overhead Stirrer Speed Range 0/4 to 530 RPM Viscosity Max. 150000 mPas (more) Setting Accuracy Speed 1 ± RPM Features - Multilingual TFT display - Programmable functions - Integrated temperature measurement - Interval operation - Timer function - Adjustable safety circuit - Locked function - Infinitely adjustable speed - Overload protection - Short-term overload operation - Slim casing - Quiet operation - Error code display - H 67.60 temperature sensor and WH 11 WiCo holder included in delivery Extremely powerful laboratory stirrer for highly viscous applications for quantities up to 100 l (H2O). It is designed with a removable wireless controller and a digital TFT display. It automatically adjusts the speed through microprocessor controlled technology within the speed range of 0/4 - 530 rpm (two speed ranges). The stirrer comes equipped with a RS 232 and a USB interface to control and document all parameters. An integrated torque trend display is provided for the measurement of viscosity changes. Safety circuits installed ensures automatic cut-off in an anti-stall or overload conditions. Continuous comparison of shaft speed to desired speed is maintained and variations are adjusted automatically. This guarantees a constant speed even with changes in viscosities of the sample.

Heidolph 036300380 Overhead Stirrer Impeller, TR 20 Radial Flow Due to the jagged shape of the stirr (more)er blade, the radial flow impeller TR 20 is ideally suited for the construction of emulsions and the gassing or foaming of liquids in vessels with the following characteristics: ideal vessel diameter: 80-140 mm, ideal ground clearance: 14-28 mm, ideal filling level: 80-140 mm, ideal volume: 400-2,200 ml. The radial-flow impeller TR 20 has a total length of 400 mm and is made of stainless steel. Its stirrer shaft has a diameter of 8 mm. INCLUDED: The Heidolph 036300380 Overhead Stirrer Impeller, TR 20 Radial Flow includes: - Manufacturer's Documentation - 3 Year Manufacturer's Warranty