Agilent LCMS 6410 with 1200 HPLC

This CTC Analytics Leap HTC PAL Autosampler Heating and Cooling HPLC was removed from a university l (more)ab where it was surplus to requirements. All units are in good cosmetic condition and powered up. The CTC Analytics Leap HTC PAL Autosampler was tested with a digital thermometer (not included). We are unable to test further at our facility. Autosampler consists of: CTC Analytics main unit MXY 01-01BSerial No. 113351 CTC Analytics Injector Column MZ01-00DSerial No. 1284 2 x CTC Analytics Pumps MZ01-00DSerial Nos. 3022, 3216 Supercool Box27 sample tray heating and cooling 3 x drawers 20cm x 12cmSerial No. CCO-00103 CCT Analytics Peltier Thermostat unit MN 03-02 CCT Analytics Power Supply MN01-00 CCT Control Pad and Screen MB 01-00A Needle wash unit Included:4 x power leads1 x data cableSolvent shelf with 1 litre glass Scott Duran bottle

Job Lot of Assorted Agilent Parts These were removed from a laboratory where they were surplus to r (more)equirements. All items are untested and are in reasonably good used condition. Due to the items being untested and missing various parts, this job lot is listed as Spares or Repairs. All items included: Dionex Ultimate 3000 Autosampler Injection ValveP/N - MHP7900-000S/N - 13756 Yokogawa G1314-66521-VWM Board for Agilent 1100No Info on Board Agilent Thermo Waters Systec 9000-1472 ZHCRP/N - 9000-1472S/N - 1022482 VEXTA STEPPING MOTOR C7693-9012K-C1Model - C7693-9012K-C1 ERC-6210 Air Vacuum PumpModel - ERC-6210S/N - 963647A-00244C* MAXON MOTOR DC 526770 Agilent HPLC Standard Flow Cell, 4MPa(40 bar), G1314-60086S/N - 5487 Sena Parani-SD1000S/N - 1A2D3E

This Agilent Technologies HPLC 1200 Series G1311A Quat Pump Quaternary was removed from a university (more) lab where it was surplus to requirements. The item is in good cosmetic condition and powered up, as seen the item is missing the front door panel. We are unable to test this item further at our facility.

This Dionex ICS-3000 ION Chromatography System was removed from a university lab where it was surplu (more)s to requirements. The system has been professionally serviced and is in full working order. A full report is available on request. It is in good cosmetic condition with minor marks. SP:Powers on okCommunicates with ChromeleonRetrieves data configurationPump primes and operates DC:Firmware 2.6.0Powers on okCommunicated with ChromeleonRetrieves data configurationInject valve separates okOven heats to set temperature on both zonesAll ok AS50:Firmware 1.21USB rev 1.00All diagnostics tests passedAll internal tests passedInject port alignment checked and okNew Syringe fitted.

System contains: 2 Solvent cabinets 2 Capillary pumps 1 Well-plate samplers 2 Autosampler thermostat (more)s 1 Thermostatted colomn compartment 1 Diode array detector 1 Handheld control module Vacuum degasser cel is missing in the vacuum degasser Capillary pump: Settable column flow range: 0.01 – 20 µl/min Recommended column flow range: 1 – 20 µl/min Column flow precision: < 0.7 % RSD or 0.03 % SD (typically 0.4 % RSD or 0.02 % SD), at 10 µl/min and 50 µl/min column flow (based on RT, default setting) Optimum composition range: 1 to 99% or 5 µl/min per channel (primary flow), whatever is greater Composition precision: < 0.2 % SD, at 10 µl/min (20 µl flow sensor), 50 µl/min (100 µl flow sensor) and 1 ml/min (normal mode) default setting Delay volume: Typically 3 µl from the electronic flow control to the pump outlet for flow rates up to 20 µl/min. Pressure range: 20 to 400 bar (5880 psi) system pressure Compressibility compensation: User-selectable, based on mobile phase compressibility Recommended pH range: 1.0 – 8.5, solvents with pH < 2.3 should not contain acids which attack stainless steel. Upper pH range is limited by fused silica capillaries. Well-plate sampler: Safety features: Leak detection and safe leak handling, low voltages in maintenance areas, error detection and display Injection range: 0.01 – 8 µl in 0.01 µl increments Precision: Typically < 0.5 % RSD of peak areas from 5 – 40 µl, Typically < 1 % RSD from 1 – 5 µl, Typically < 3 % RSD from 0.2 – 1 µl Sample viscosity range: 0.2 – 5 cp Sample capacity: 2 × well-plates (MTP) + 10 × 2 ml vials, 100 x 2 ml in one tray, 40 x 2 ml in half tray Injection cycle time: Typically < 30 s using following standard conditions: Default draw speed: 4 µl/min, Default eject speed: 10 µl/min, Injection volume: 0.1 µl Carry-over: Typically < 0.05 % using the following conditions: Column: 150 x 0.5 mm Hypersil ODS, 3 µm Mobile phase: Water/Acetonitrile = 85/15 Column Flow rate: 13 µl/min Injection volume: 1 µl caffeine (=25ng caffeine), 1 µl water to test carryover. Outside wash of needle before injection: 20 sec with water using flush port Autosampler thermostat: Temperature range: setable from 4 °C to 40 °C in 1 ° increments Temperature accuracy at ambient temperatures < 25 °C and humidity < 50%: – 1°C to + 4 °C at a setpoint of 4 °C Temperature accuracy at ambient temperatures > 25 °C and/or humidity > 50%: – 1°C to + 5 °C at a setpoint of 4 °C Thermostatted colomn compartment: Temperature range: 10 degrees below ambient to 80 °C, up to 80 °C: flow rates up to 5 ml/min Temperature stability: ± 0.15 °C Temperature accuracy: ± 0.8 °C (± 0.5 °C With calibration) Column capacity: Three 30 cm Warm-up/cool-down time: 5 minutes from ambient to 40 °C, 10 minutes from 40 – 20 °C Dead volume: 3 µl Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN via other series module Safety and maintenance: Extensive diagnostics, error detection and display (through control module and Agilent ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Diode array detector: Detection type: 1024-element photodiode array Light source: Deuterium and tungsten lamps Wavelength range: 190 – 950 nm Short term noise (ASTM) Single and Multi-Wavelengt: ± 1 × 10-5 AU at 254 and 750 nm Drift: 2 × 10-3 AU/hr at 254 nm Linear absorbance range: > 2 AU (upper limit) Wavelength accuracy: ± 1 nm Self-calibration with deuterium lines, verification with holmium oxide filter Wavelength bunching: 1 – 400 nm Programmable in steps of 1 nm Slit width: 1, 2, 4 , 8, 16 nm Programmable slit Diode width: < 1 nm Flow cells: 13 µl volume, 10 mm cell path length and 120 bar (1760 psi) pressure maximum Control and data evaluation: Agilent ChemStation for LC Analog outputs: Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, two outputs Communications: Controller-area network (CAN), GPIB, RS-232C, APG Remote: ready, start, stop and shut-down signals, LAN optional Safety and maintenance: Extensive diagnostics, error detection and display through control module and ChemStation), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. GLP features: Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user-settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with built-in holmium oxide filter. Handheld control module: The control module provides complete local control and monitoring of a single module or an entire Agilent series system. There is no data evaluation in the control module. The control module allows you to do a variety of HPLC tasks including automated sample preparation and injection, isocratic, gradient and multiple method analyses.

System consists of: Jasco UV-1570M Intelligent UV Detector Jasco LG-1580-02 Ternary Gradient Unit Ja (more)sco PU-1580 Intelligent HPLC Pump Jasco AS-1555 Intelligent Sampler 2 Alltech Elite Degassing System PC