MARSHALL Select MS-CE6000 Benchtop Centrifuge, 6,000 RPM

MSE Mistral 3000i Benchtop Centrifuge This was removed from a university lab where it was surplus to (more) requirements. Although the unit is in good cosmetic condition and powers on, it is unable to run a cycle or reduce temperature. Additionally included: 1 x MSE RotorModel BS4402 7 x Swinging Buckets:Volume: 250ml Bucket Adaptors: 6 x BlueHolds: 12x 5ml Vials 7 x GreyHolds: 4 x 12ml Vials 8 x MSE BrownHolds: 1 x 100ml VIals 1 x Hex Key Locking Bar

This Sanyo MSE Mistral 2000R Refrigerated Benchtop Centrifuge was removed from a university lab wher (more)e it was surplus to requirements. The unit has been tested and is in working order. The RPM could be set up to 6500 but the rotor would only run up to 4500rpm. It was tested with a digital thermometer (not included).When the temperature was set to 4˚c, the thermometer read 5˚cWhen the temperature was set to -4˚c (minimum) the thermometer read -5˚c There is a Rotor inside with 4 x Buckets and 2 x Yellow 50ml Adaptors. It is in reasonably good cosmetic condition but has some minor marks from use.

This Sigma 1-15K Refrigerated Benchtop Centrifuge was removed from a university lab where it was sur (more)plus to requirements. The unit has been recertified by a service engineer. It is in full working order. It has had a new gas strut fitted, but the lid can get stuck. Once it is opened it will repeatedly open, but when left for an amount of time it can get stuck again. It is in excellent cosmetic condition with some minor marks from use.

This Thermo Scientific Heraeus Fresco 21 Refrigerated Benchtop Centrifuge was removed from a univers (more)ity lab where it was surplus to requirements. The unit was inspected by a service engineer. They replaced the display with one from an older model. It is now green. It is fully working up to 14800rpm and has been fully temperature tested. It is in excellent cosmetic condition with only minor usage marks.

WTW OXI 3205 portable oximeter + Cellox 325 probe With Cellox 325 probe Waterproof dissolved oxygen  (more)measuring instrument Battery type: 4 x 1.5 V AA rechargeable batteries or 4 x 1.2 V NiMH rechargeable batteries Compensation and correction of atmospheric pressure: Automatic from 500 to 1100 mbar Protection class: IP 67 Screen display: backlit graphic LCD Dissolved O2 measuring range: 0.00 to 90 mg/L Dissolved O2 accuracy: ±0.5% Dissolved O2 resolution: 0.01, 0.1mg/L Temperature precision/accuracy: ±0.1°C Working/Operating/Use Temperature: -5 to 50°C Net weight: 2KG

Demo device. Unused & in original packaging. 2022 model. Great condition. 6 months warranty. Technic (more)al specifications: - External dimensions (WxDxH): 780 x 970 x 945 mm - Internal dimensions (WxDxH): 607 x 670 x 629 mm - Internal volume: 255 l (usable: 162 l) - Rack dimensions: 560 x 500 mm (capacity: 12 pcs., scope of delivery: 3 pcs.) - Max. weight load per rack: 10 kg - Max. weight load per device: 30 kg - Device weight: 97.5 kg - Adjustable temperature: +3 °C - 55 °C - Ambient temperature: +18 °C - +34 °C - Temperature deviation: +/- 0.1 °C

Elix systems have been designed to deliver the highest pure water quality for your regular laborator (more)y applications and instrument feed. Elix is suited to every user’s needs in today’s demanding laboratory environment. Elix water quality is ideal for the preparation of reagents and buffers, for microbiology media, hydroponics or histology. It is also the best feed for all Milli-Q and Super-Q ultrapure water systems, as well as instruments such as glassware washers, autoclaves and hydrogen generators. Superior and consistent Type 2 water quality – “Superior”, as resin beads are not degraded by exposure to harsh regeneration chemicals. “Consistent”, as the continuous regeneration avoids the drawbacks of quality variations from resin exhaustion. Cost & labor savings – Elix module contains special carbon beads at its cathode therefore, does not require water softening. Its self-regeneration technology avoids the hassle and costs around DI cartridge replacement. Elix is “green” consuming low energy with a small carbon footprint. Long lasting technology – thanks to its proven design, the module continuously regenerates its resin beads without the need for any maintenance. Elix pure water is irradiated by a bactericidal UV lamp before entering the storage tank. The reservoir design maintains consistent purity of stored water. The vent filter provides effective protection against airborne contaminants and the ASM, Automatic Sanitization Module, prevents biofilm formation. Elix water can then be sent by a distribution pump to feed instruments or a distribution loop. They can be integrated into a centralized system, providing total control of all parameters within the system itself as well as within the external pure water distribution loop. Water Specifications: Resistivity at 25 °C: > 5 MΩ•cm TOC: < 30 ppb Bacteria: < 10 CFU/mL Silicate removal: > 99.9 % Production flow Rate: 20 L/h Feed water: Water quality: Potable tap water Feed water conductivity at 25 °C: < 2000 µS/cm Feed water pressure: 2 – 6 bar Feed water temperature: 5 – 35°C Feed water chlorine: Application Specialist will determine pretreatment required Feed water fouling index: Application Specialist will determine pretreatment required Feed water pH: 4 – 10 pH units Feed water connection: ½ in Gaz M System Specifications: Dimensions (H x W x D): 734 x 662 x 441 mm Operating weight: 45 – 62 kg Data port connection: RS232 Including 200 L storage tank Excluding new filters

S+B Sink Ice Blue 600

HX7.4P2 H is a beam scale made of stainless steel. 4-load-cell, 2-component mechanical design stands (more) for high measurement accuracy. The weights may be loaded onto the pan using a forklift or a transporter crane, supplementary handles significantly facilitate the transport. The device has been fitted with a 7&quot; colour display and a diode bar graph. Blinking green and red diodes show current load mass, the mass is presented in reference to the scale range or declared minimum and maximum thresholds. At the back of the housing there are hermetic connectors of RS232, RS485, USB and Ethernet communication interfaces, plus digital inputs/outputs and analogue output. This enables cooperation with external devices such as barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. With use of the bracket you can either place the indicator at any flat horizontal surface, or fix it to the wall adjusting the tilt respectively to suit your needs. The terminal&#39;s software allows carrying out processes such as weighing, parts counting, dosing, labelling, formulations and percent weighing. Indicator&rsquo;s system of information is based on databases (users, products, weighings, packaging, formulations, customers) and ALIBI memory which guarantees stored data safety.

Ohaus 30314822 4 x 145ml Swing Out Rotor The Ohaus 30314822 4 x 145ml Swing Out Rotor accommodates a (more) capacity of up to 4 x 145 ml. This rotor is designed for use with Ohaus FC5718, FC5718R, FC5714, and FC5720R series centrifuges. The Ohaus 30314822 Fixed Angle Rotor reaches a maximum speed of 4,500 RPM and a maximum Relative Centrifugal Force of 3,350 x g. INCLUDED: The Ohaus 30314822 4 x 145ml Swing Out Rotor includes: - Ohaus 30314822 4 x 145ml Swing Out Rotor - Manufacturer's Documentation - 1 Year Manufacturer's Warranty