HETTICH EBA21 Benchtop Centrifuge

This Sanyo MSE Mistral 2000R Refrigerated Benchtop Centrifuge was removed from a university lab wher (more)e it was surplus to requirements. The unit has been tested and is in working order. The RPM could be set up to 6500 but the rotor would only run up to 4500rpm. It was tested with a digital thermometer (not included).When the temperature was set to 4˚c, the thermometer read 5˚cWhen the temperature was set to -4˚c (minimum) the thermometer read -5˚c There is a Rotor inside with 4 x Buckets and 2 x Yellow 50ml Adaptors. It is in reasonably good cosmetic condition but has some minor marks from use.

This Sigma 1-15K Refrigerated Benchtop Centrifuge was removed from a university lab where it was sur (more)plus to requirements. The unit has been recertified by a service engineer. It is in full working order. It has had a new gas strut fitted, but the lid can get stuck. Once it is opened it will repeatedly open, but when left for an amount of time it can get stuck again. It is in excellent cosmetic condition with some minor marks from use.

Heraeus Labofuge 400 Function Line Benchtop Centrifuge This was removed from a university lab where  (more)it was surplus to requirements. The unit powers up and runs smoothly up to 3500rpm. It is in reasonable cosmetic condition with light marks and rusting. Heraeus Rotor #81794 x Buckets #8172 Ch.003515

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

New Brunswick Scientific Innova U725-G Ultra Low-Temperature Freezer Lab This item was removed from  (more)a university where it was surplus to requirement. It is in good cosmetic condition and powers on; however, upon activation, the pump experiences a short circuit, which prevents further testing. Therefore, this item is listed as Spares/Repair. It features 2 x Shelves: 55 x 84cm

Job Lot of 18 Electro Nickel Clifton 1026E Boiling Baths with ER1 Regulators These were removed form (more) a university lab where they were surplus to requirements. The units are all in good working order.

Yamato DKL-601C Forced Convection Oven 150L, 115V Temperature Range Room temp. +10~260°C Temperatur (more)e Distribution Accuracy ±2.5°C (at 260°C) Chamber Volume 150L Features - Fixed temperature, Quick auto stop, Auto stop, and Auto start operating modes with easy control capabilities - Settings can be made digitally with the dedicated operation menu keys or the ▲/▼ keys - Calibration off-set as auxiliary function - Self-diagnostic functions, MCB with over current protector, hydraulic standalone overheat prevention device Economical forced convection 150L constant temperature oven with basic functions and safety features. Fixed temperature, Quick Auto stop, Auto stop, and Auto start operating modes with easy control capabilities. Settings can be made digitally with the dedicated operation menu keys or the ▲/▼ keys. Operating temp ambient +10~260°C. INCLUDED: The Yamato DKL-601C Forced Convection Oven 150L, 115V includes: - 2 x Stainless Steel Shelf Plates w/ 4 x Brackets - Power Cord - Operator's Manual - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

The HX7.4N H scale is a device controlled by means of the PUE HX7 indicator, and it has been equippe (more)d with a 4-load-cell ramp platform made of stainless steel, AISI 304. This robust design facilitates weighing of heavy loads in humid environment. The ramps enable easy loading and unloading. Indicator with a colour 7” graphic display and a diode bar graph allow to observe visualisation of a current load mass presented in relation to the scale range or declared minimum and maximum thresholds. This makes the operation significantly easier. At the back of the housing there are hermetic connectors of RS232, RS485, USB and Ethernet communication interfaces, plus digital inputs/outputs and analogue output. This enables cooperation with external devices such as barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. With use of the bracket you can either place the indicator at any flat horizontal surface, or fix it to the wall adjusting the tilt respectively to suit your needs. The terminal's software allows carrying out processes such as weighing, parts counting, dosing, labelling, formulations and percent weighing. Indicator’s system of information is based on databases (users, products, weighings, packaging, formulations, customers) and ALIBI memory which guarantees stored data safety.