Hermle SIEVA-3 Filtration Centrifuge w/ 500ml Perforated Centrifugal Basket

Maximum RCF with fixed angle rotor: 20913 x g Maximum RCF with swing-bucket rotor: 4500 x g Maximum  (more)RCF with plate rotor: 3486 x g Speed range: 200 – 14000 rpm Temperature range: -9 °C to 40 °C Maximum capacity: 4x 750 mL/4x MTP Acceleration/braking ramps: 10/10 Timer: 1 min to 99 min, continuous, short-spin Dimensions (WxDxH): 700 x 608 x 345 mm Weight: 99 kg Equipped with: 1x Eppendorf A-4-81 swing-out rotor (max 4000 rpm) 4x Eppendorf bucket 4x Eppendorf bucket aerosol-tight lid 4x Eppendorf MTP carrier 4x Eppendorf insert (10x 15 mL falcon tube capacity) 4x Eppendorf insert (5x 50 mL falcon tube capacity)

Maximum capacity: 4 x 100 ml Maximum density: 1.2 kg/dm3 Maximum speed: 6000 RPM Maximum force: 4186 (more) RCF Maximum kinetic energy: 3000 Nm Noise level (dependent on rotor): ≤ 65 dB(A) Dimensions (WxDxH): 368 x 437 x 261 mm Weight: 15.6 kg No rotor included

This Sorvall H6000/HBB-6/HLR-6 5000rpm Swinging Bucket Rotor was removed from a university lab where (more) it was surplus to requirements. The unit is in good cosmetic condition with only minor marks from use. It has 6 x 1000ML Buckets. P/N 44040 The rotor is rated for 5000rpm Max. The normal terms and conditions do not apply to this item. This item is non returnable and non refundable.

Cepa Z-41 High Speed Centrifuge This was removed from a university lab where it was surplus to requi (more)rements. The unit powers up and is in working order. It runs on a timer delay so takes a few moments to start working. It is in good cosmetic condition.

Hermle Compact Centrifuge with Combination RotorFeatures - Microprocessor with large LCD display - E (more)lectrical lid lock - Quick access to samples - Active imbalance identifi cation and cut-off - Air Cooling System - Quick Acceleration and Deceleration - Noise level < 60 dBA, at max. speed - Easy removal of rotor, without tools - Manufactured in accordance to International - Safety Regulations, i.e. IEC 61010 The Z207-A-CMB includes a convenient combination rotor that holds 4 x 15 ml and 4 x 50 ml tubes in the same rotor. With the combination rotor there's no longer a need switch rotors, or use adapters to centrifuge 15 ml and 50 ml tubes for tissue culture. You can even process them simultaneously! Along with the unique combination rotor, the Z207-A-CMB features the unique EZ-Scroll™ touch pad which gives you ease of control and a modern feel. An advanced microprocessor control allow for setting/displaying of the rotational speed in either rpm or rcf in increments of 10. In addition to retrieving saved programs, the easy to use front panel can be used to adjust accel/decel rates, run time, and change the end of run alarm tone. There is also a momentary spin function that will run while the button is pressed. Additionally the Z207-A-CMB features a sleep mode to save energy by shutting off after a certain time if not being used while on, which can be toggled on or off easily. INCLUDED: The Hermle Compact Centrifuge with Combination Rotor includes: - Combination Rotor - Power Cord - Operator's Guide - Manufacturer Documentation - 5 Year Manufacturer's Warranty

System consists of: Agilent G1322A Degasser Agilent G1311A Quaternary Pump Agilent G1313A Autosample (more)r Agilent G1316A Thermostatted Column Compartment Agilent G1314A Variable Wavelength Detector

Olympus BX61 Microscope With BX-UCB And U-HSTR2 Control Units This microscope system was removed fro (more)m a university where it was surplus to requirement. All units are in good cosmetic condition and in good working order. The items included are as follows: 1 x Olympus BX61 Microscope Model: BX61TRF.Serial No 7M25426 1 x Olympus BX-UCB.Serial No. 0D07119 1 x Olympus U-HSTR2.Serial No. 2E16101 1 x Olympus U-LH100-3 Light UnitSerial No. 7J12122 2 x Olympus WHN10x/22 Eyepiece. 1 x PlanApo N 60x/1.42 oil /17/FN26.5.1 x UplanSApo 100x/1.40 oil/17/FN26.5.1 x UPlanFL N 10x /0.30 /FN26.5.1 x PlanApo N 1.25 x/0.04 /FN26.5.2 x data cables

Large-size additional display is an accessory of load-cell scales. stainless steel housing 6 digits  (more)of 4,5 inches in height (11,2cm) white diode backlight Features Robust and Resistant Stainless Steel Housing The WWG-2 LCD display is housed in a stainless steel housing, which enables its operation in harsh industry conditions. The display can be installed on the table top or mounted on the wall. The WWG-2 LCD features white diode backlight and clear display indicating digits of 4.5" (11.2cm) height. Communication Communication with indicators (weighing instruments) is carried out via RS22 or RS485 connectors. Depending on the installation option, the display is powered by 230VAC or 7-24VAC.

Do you need a moisture analyzer that not only determines moisture or dry matter content with impress (more)ive accuracy, but also performs a digital audit, responds to your voice commands and sends you light messages? If so, learn about the functionality of the ELLIPSIS series of moisture analyzers: It Dries in 4 Ways The MA 5Y.IC Moisture Analyzer offers you four drying profiles: standard, mild, fast and step. The standard profile is the usually used drying profile. It allows the most accurate determination of moisture content. The mild profile is designed for drying substances that are sensitive to the rapid heat released by the filaments, which heat full power at the initial stage of the process. An example of such a substance is leather. You will use the fast profile for samples with significant moisture content – of the order of even several tens of percent. The step profile will be ideal for drying substances that contain more than 15 percent moisture. Within this profile you can define any three temperatures. You will choose the values of temperature and duration of heating experimentally. What Drying Temperature Should I Set? The drying temperature determines the duration of the process. Its value depends on the type of material. If the temperature is too low, it will under-dry the sample and, consequently, unnecessarily increase the measurement time, while if it is too high, it will cause a burning effect on the material. The drying temperature for the traditional (oven) method is determined by industry or factory standards. If there are no standards, you will select the temperature experimentally. The maximum drying temperature on the MA 5Y.IC Moisture Analyzer is 160°C. How Do I Finish the Drying? In 4 Ways The MA 5Y.IC Moisture Analyzer has four finish modes: automatic, manual, time-defined and user-defined. Automatic mode You define the moisture loss limit value in 60 seconds. When the moisture analyzer reaches the set criterion, the measurement will automatically end. Manual mode You terminate the measurement yourself by pressing the STOP button. Time-defined mode The measurement ends after the set time has elapsed regardless of the result. You have up to 99 hours 59 minutes to manage! User-defined mode When you remove all volatiles from a sample, by definition, its mass should be constant. During drying, the dry mass of the sample is defined by a condition: if the mass of the sample is stable within 1 mg during the observation time (Auto 1-5), we consider that all volatile components have been removed from its structure. Digital Weighing Auditor Ensures that your moisture analyzer is ready for use. What is more, it informs about the need for a moisture analyzer inspection or a periodic audit of the moisture analyzer’s accuracy and sensitivity. 10-Inch Display Bigger screen – 10’’ – means more information in one place. On the new ELLIPSIS terminal, you will see up to 3 screens, widgets, graphs, statuses, notes, handy measurement history. Uncompromising User Verification For the first time ever, the moisture analyzer will verify the user using a password, RFID card, fingerprint reader, facial recognition mechanism, or any combination of these. Ambient Light – an Innovative Way for the Moisture Analyzer to Communicate With the User The light colour will tell you about status, process results, procedures, or alerts. Hotspot Use the moisture analyzer on any device connected to it. This can be a smartphone, tablet, or computer. RFID ELLIPSIS works with RFID tags* that can be used to tag your products or formulation ingredients in the database. They can also be used to identify a user. Live Note – Note Down Your Conclusions It’s the first time you can add a voice memo to a measurement series or procedure report. If you prefer to write it down, ELLIPSIS allows you to add a text note. Handy Library This is where a series of recent measurements or a report ready for digital signature, according to 21 CFR Part 11, can be found. Widgets Prepared to display what you need most at any given moment. 21 CFR Part 11 Do you work in the pharmaceutical industry? Do you need a digital signature? We are offering the moisture analyzer which as a standalone fully meets the requirements of 21 CFR Part 11/ EU GMP Annex 11. Full data security Electronic signatures Validations Electronic records Audit trails Modbus TCP/IP is one of the most popular communication protocols in industrial automation. Implementing it in the 5Y balances and CY10 scales makes the devices of this series friendly to automation integrators. A balance or scale in a Modbus system is a slave device and performs tasks specified by the master device which is most often a PLC. Protocol Modbus TCP/IP in the 5Y balances and C10 scales enables, among other things, the realization of mass readout, zeroing and tare functions of the device, as well as tare settings and MIN and MAX thresholds. * RFID ISO/IEC 14443 Type A, 13.56 MHz

The HX5.EX scale is a modern weighing instrument assuring fast and reliable measurement in hazardous (more) areas classified as zones 1/21 and 2/22. To ensure precision and excellent measurement repeatability, high quality electronic components are used. The weighing platforms offered in wide range of dimensions and maximum capacities, this combined with excellent metrological parameters enables easy selection of an instrument that meets the most demanding requirements. Standard version of the scale is equipped with 2 serial, intrinsically safe RS232 communication interfaces, and with one RS485 interface. They facilitate cooperation with equipment intended for operation in hazardous areas. Possibility to add digital inputs/outputs extends the range of instruments compatible with the indicator by automatic elements compliant with ATEX directive. More demanding customers can use the IM01.EX module, installed in the safe area, which extends the available connectors by Ethernet, USB, 4-20mA/0- 10V analog outputs, Profibus DP and additional digital inputs/outputs. This enables cooperation with external devices: barcode scanners, printers, external displays, control buttons, light signalling towers, other controlling/signalling devices, systems for automatic process control and superior IT systems. Scale operation requires use of a dedicated PM01.EX power supply, which is not a standard scale component. To operate the scale, order a selected type of the dedicated intrinsically safe power supply. Power supply types: PM01.EX-1 - power supply for operation in ATEX area. Used when it is required to connect the power supply to voltage source placed in hazardous area. PM01.EX-2 - power supply for operation outside ATEX area. Used when power supply connection to voltage source is carried out outside hazardous area. Complex software enables carrying out many tasks connected with mass measurement, e.g. parts counting, checkweighing and statistics. The scales feature user-friendly graphic interface, which can be customized using widgets. This and the large colour display of high resolution guarantee easy and clear transmission of data on current process. Colour bar graph significantly influences performance by signalling whether the weighing result is within declared thresholds or not.

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW