Labnet Spectrafuge 6C no 2

This Jouan B4i Benchtop Centrifuge was removed from a university lab where it was surplus to require (more)ments. The unit powers up and is in good working order. It is in good cosmetic condition with minor marks. This item includes the following rotor: Thermo Jouan High Throughput Swing-Out Rotor Model S40Max Load 2.00kgMax speed 4300 (rpm) This item ran at 4000rpm with S40 Rotor fitted.As stated in the manual, the maximum speed for a swing-out rotor on this unit is 4000 rpm.

MSE Mistral 3000i Benchtop Centrifuge This was removed from a university lab where it was surplus to (more) requirements. Although the unit is in good cosmetic condition and powers on, it is unable to run a cycle or reduce temperature. Additionally included: 1 x MSE RotorModel BS4402 7 x Swinging Buckets:Volume: 250ml Bucket Adaptors: 6 x BlueHolds: 12x 5ml Vials 7 x GreyHolds: 4 x 12ml Vials 8 x MSE BrownHolds: 1 x 100ml VIals 1 x Hex Key Locking Bar

This Sanyo MSE Mistral 2000R Refrigerated Benchtop Centrifuge was removed from a university lab wher (more)e it was surplus to requirements. The unit has been tested and is in working order. The RPM could be set up to 6500 but the rotor would only run up to 4500rpm. It was tested with a digital thermometer (not included).When the temperature was set to 4˚c, the thermometer read 5˚cWhen the temperature was set to -4˚c (minimum) the thermometer read -5˚c There is a Rotor inside with 4 x Buckets and 2 x Yellow 50ml Adaptors. It is in reasonably good cosmetic condition but has some minor marks from use.

Sorvall Legend T Benchtop Centrifuge with 4600rpm Rotor This was removed from a university lab where (more) it was surplus to requirements. The unit powers up and is in full working order. It is in reasonably good cosmetic condition with marks from use. Included are; 1x Sorvall RotorP/N: 75006445S/N: 002518 4x Sorvall swinging bucket Heraeus AdaptorsP/N: 75006449

MARSHALL Select MS-CE4000 Benchtop Centrifuge, 4,000 RPM Maximum Speed 4,000 RPM Maximum RCF 2,250  (more)x g Maximum Capacity 6 x 50ml Features - Steel body construction with a plastic-sprayed surface for durability and aesthetic appeal - Low noise operation at less than 65 dB(A) ensures a quiet laboratory environment - Features a low temperature rise during use, preserving sample integrity - Equipped with a maintenance-free DC brushless motor for reliable and smooth operation - Microprocessor control with door cover protection enhances safety - Alarm monitoring function for real-time tracking of lock and motor status - User-friendly interface facilitates intuitive setup and operation - Real-time display of centrifugal force and operational parameters - Push-button programming and digital tube display for easy operation and monitoring - Supports various fixed-angle rotors to accommodate different testing needs - Compact dimensions make this centrifuge ideal for benchtop use The MARSHALL Select MS-CE4000 Benchtop Centrifuge is designed for optimal performance and durability, achieving a maximum speed of 4,000 RPM and an RCF of 2,250 x g. Its capacity to handle up to 6 x 50 ml tubes makes it suitable for a range of laboratory applications, from biochemistry to pharmacy. The centrifuge features a robust steel body with a plastic-sprayed surface, combining strength with an aesthetically pleasing appearance. It operates quietly with a noise level below 65 dB(A) and maintains a low temperature rise during operation, ensuring sample integrity. Equipped with a maintenance-free DC brushless motor and microprocessor control, the MS-CE4000 ensures smooth and reliable operation. The unit's safety is enhanced with door cover protection and an alarm monitoring system that keeps track of the lock and motor status. Its user-friendly interface includes push-button programming, a digital tube display for real-time parameter monitoring, and the ability to set and view centrifugal speed and time. The centrifuge is versatile, supporting various fixed-angle rotors to meet different experimental needs. With its compact dimensions (17.7 x 14.6 x 11 inches), this centrifuge is an excellent choice for laboratories seeking a reliable, multi-functional device. INCLUDED: The MARSHALL Select MS-CE4000 Benchtop Centrifuge, 4,000 RPM includes: - Power Cord - Operator's Manual - Manufacturer's Documentation - 1 Year Manufacturer's Warranty

The offered instrument / system is fully functional tested and ready to use. FURTHER DETAILS TO FOLL (more)OW

Revco Scientific LIC-2090W14 Ultra Low Temperature Chest Freezer ULT This item was removed from a un (more)iversity where it was surplus to requirement. The unit powers up and is in good working order (thermometer not included). The item's exterior shows wear and tear, with scratches, scuffs, and minor dents, while the interior has light rust. The door seals are deteriorated, and the top lid fails to stay open due to damaged hinges and weakened lid supports, but overall it is still in working order. Included with the freezer are five rack units: 1 x 2 compartment rack 29 x 29 x 56cm 3 x 16 compartment rack 25 x 14 x 56cm 1 x 16 compartment rack 28 x 14 x 56cm

This Bio-Rad PDS-1000/He Biolistic Particle Delivery System was removed from a university lab where  (more)it was surplus to requirements. The unit powers up but we were unable to test ti further at our facility. It is in good cosmetic condition with marks from use. Included with it are; 1 x Circle Seal Controls SV11A32P4P33 Solenoid Valve (plugs into back of PDS) 1 x Regulator - Tescom Model no. 44-1812-24V-147

Polyscience P35N5A101B IP-35 Immersion Probe Cooler, 1.75 Rigid Coil Probe, -35 to +40C, 120V, 60Hz3 (more)D Visualization of the Polyscience Immersion Probe CoolerThe rendered image can be freely rotated in a full 360-degree view, allowing you to zoom in, pause, and explore every angle. For enhanced detail, the rendering can also be displayed in full-screen mode. This 3D model is designed exclusively for visualization purposes and may not accurately represent the actual appearance of your product. Your browser does not support iframes. .rendering-block:nth-child(2) { width: 292px;}PolyScience Low Temperature Coolers enhance and simplify low-temperature laboratory work, providing rapid, low-cost cooling of liquids to temperatures as low as -100C. Typical applications include the cooling of exothermic reactions, vapor and solvent trapping, and impact testing. They’re also ideal for extending the temperature range of non-refrigerated circulators to below ambient and boosting the cooling capacity of refrigerated circulators. Enhance and simplify your low-temperature laboratory work with a PolyScience Low Temperature Cooler. Available in both immersion probe and flow-through styles, they provide rapid, low-cost cooling of liquids to temperatures as low as -100C. Typical applications include the cooling of exothermic reactions, freeze point determinations, freeze drying, impact testing, lyphilization, and vapor and solvent trapping. Features Continuous cooling to temperatures as low as -100C Designed to run at maximum cooling An economical alternative to dry ice or liquid nitrogen Excellent for trapping applications, freeze drying, and rapidly cooling small volumes of liquids INCLUDED: The Polyscience P35N5A101B IP-35 Immersion Probe Cooler, -35°C to 40°C, 1004W; 120V includes: - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty

Benchmark BioClave Mini Research Autoclave Despite the space-saving exterior dimensions of the Biocl (more)aves, the stainless steel chambers are surprisingly large, accommodating a variety of liquids, media, instruments, glassware, plasticware and other common research laboratory items. Both of these benchtop models include a mechanical and electrical safety interlock that prevents the door from being opened until the pressure has reached zero PSI. With a large digital display and fully automatic operation, all segments of the cycle (fill, sterilize, exhaust and dry) commence and run to completion by simply pressing the start button. An optional thermal mini-printer is also available for providing a record of sterilization parameters and a USB drive can be used to record settings and transfer them to a PC. The 8 liter BioClave Mini is preprogrammed to meet basic sterilization needs. Temperature can be selected at either 121C or 134C, and the sterilization time is fully adjustable. The economical BioClave Mini is the ideal choice wherever benchtop sterilization is required and space is limited. INCLUDED: The Benchmark BioClave Mini Research Autoclave includes: - Power Cord - Operator's Guide - Manufacturer's Documentation - 2 Year Manufacturer's Warranty